Installing both left VANOS adjusters

Check the camshaft positions of bank 1.
The cams (1) must be in the position shown.

The increment wheels (2) must form a line to the exhaust camshaft bearing cap and to the intake camshaft bearing cap.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Description is for right component only. The procedure on the left side is identical.

NOTE: To provide a better overview: Schematic diagram with partially hidden components.

Make sure that the ground surfaces (2) of the camshafts point up.
Make sure that the rounded surfaces (1) point downwards to the cylinder head.
Check and evaluate the timing once again.

Courtesy of BMW OF NORTH AMERICA, INC.
Position special tool 2 249 117 (1) on the camshafts of cylinder bank 1.
Secure the camshafts using special tool 2 249 117 (1) .
Using 2 screws (2) of the cylinder head cover, bring special tool 2 249 117 in contact with the cylinder head until hand-tight.

Courtesy of BMW OF NORTH AMERICA, INC.
The installation position of the VANOS adjusters must be observed in every case.
IN is the intake adjuster (1) .

EX is the exhaust camshaft adjuster (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Thread VANOS adjusters (1) in and position.

Courtesy of BMW OF NORTH AMERICA, INC.
Position VANOS central valves (1) .
Tighten VANOS central valves (1) hand-tight.

Courtesy of BMW OF NORTH AMERICA, INC.
Position the slide rail (3) of the cylinder bank 2.
Tighten down screw (2) .

TIGHTENING TORQUE SPECIFICATIONS

Flat-head screw to the slide rail
Flat-head screw M6x67	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1) .

TIGHTENING TORQUE SPECIFICATIONS

Collar screw to the slide rail
Collar screw M6x48	Tightening torque	10 Nm

NOTE: RISK OF DAMAGE
Damage to timing chain or timing chain drive.
Turning the engine without chain tensioner or special tool can result in damage to the timing chain and timing chain drive.

Always turn the engine with the chain tensioner or the special tool.

Position the special tool 2 249 162 on the cylinder head and hand-tighten the screws (1) .
Exchange the screw (2) on the special tool 2 249 162 with an (M8x15) hexagon screw.

Courtesy of BMW OF NORTH AMERICA, INC.
Pretension special tool 2 249 162 using special tool 0 496 778 (00 9 460) at 0.6 Nm.
The flexible shaft on the special tool 0 496 778 (00 9 460) must not come in contact with other components, otherwise the torque value is falsified.

TIGHTENING TORQUE SPECIFICATIONS

Preload timing chain
	tightening torque	0.6 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Make straight marks on the VANOS central valves (1) and the VANOS adjusters (2) in the area of the hexagon head.
The angle must be 60°.

Courtesy of BMW OF NORTH AMERICA, INC.
Release VANOS central valves (1) in the area of the hexagon counterclockwise (in the arrow direction) until the mark at the top of the VANOS central valve is aligned with the mark at the bottom.
The rotational angle must be 60°.

Courtesy of BMW OF NORTH AMERICA, INC.
Turn the engine counter-clockwise by 90° at central bolt.
Make sure that the special tools 0 493 882 (11 9 190) (1) and 0 496 366 (11 8 570) (2) do not collide with other components.
Remove the special tool 0 496 366 (11 8 570) (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Position the special tool 0 493 882 (11 9 190) (1) in the recess on the engine block.
Turn the engine on the central bolt clockwise until the special tool 0 493 882 (11 9 190) (1) lies against special tool 0 496 366 (11 8 570) (2) .
Tighten special tool 0 496 366 (11 8 570) (3) hand-tight to the vibration absorber with a screw of the belt pulley (2) .
Remove the special tool 0 496 366 (11 8 570) (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Check the preload on the special tool 2 249 162 with the special tool 0 496 778 (00 9 460) with 0.6 Nm.
The flexible shaft on special tool 0 496 778 (00 9 460) must not come in contact with any other components, as otherwise the torque value is falsified.

TIGHTENING TORQUE SPECIFICATIONS

Preload timing chain
	tightening torque	0.6 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten VANOS central valves (1) .

TIGHTENING TORQUE SPECIFICATIONS

VANOS central valve initial torque
VANOS central valve	Joining torque	5 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Turn engine on the central bolt until the special tool is aligned with the struts on the engine block.
The special tool 0 496 366 (11 8 570) (3) must be secured with a screw (2) of the belt pulley on to the vibration absorber.
Slide the crankshaft in the installation position with the special tool 0 493 882 (11 9 190) (1) on the bars and fix it.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten VANOS central valves (1) .

TIGHTENING TORQUE SPECIFICATIONS

VANOS central valve second tightening
VANOS central valve	Snug torque 1	30 Nm
VANOS central valve	Snug torque 2	50 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Position the special tool 0 490 504 (00 9 120) (1) on the VANOS exhaust central valve.
The magnetic foot of the special tool 0 490 504 (00 9 120) must be attached to a magnetic component in the engine compartment.
Make sure that the flexible element of the special tool 0 490 504 (00 9 120) (1) does not collide with the other components.

Courtesy of BMW OF NORTH AMERICA, INC.
Set the angle-of-rotation gauge on special tool 0 490 504 (00 9 120) to "0" (arrow).

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the VANOS intake central valve until the needle on the special tool 0 490 504 (00 9 120) is at 30° (arrow).

TIGHTENING TORQUE SPECIFICATIONS

VANOS central valve third tightening
VANOS central valve	Angle of rotation	30°

Courtesy of BMW OF NORTH AMERICA, INC.

Position the special tool 0 490 504 (00 9 120) (1) on the VANOS intake central valve.
The magnetic foot of the special tool 0 490 504 (00 9 120) (1) must be attached to a magnetic component in the engine compartment.
Ensure that the flexible element of special tool 0 490 504 (00 9 120) (1) does not collide with the other components.

Courtesy of BMW OF NORTH AMERICA, INC.
Set the angle-of-rotation gauge on special tool 0 490 504 (00 9 120) to "0" (arrow).

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the VANOS intake central valve until the needle on the special tool 0 490 504 (00 9 120) is at 30° (arrow).

TIGHTENING TORQUE SPECIFICATIONS

VANOS central valve third tightening
VANOS central valve	Angle of rotation	30°

Courtesy of BMW OF NORTH AMERICA, INC.

Check the camshaft positions of bank 1.
The cams (1) must be in the position shown.

The increment wheels (2) must form a line to the exhaust camshaft bearing cap and to the intake camshaft bearing cap.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Description is for right component only. The procedure on the left side is identical.

NOTE: To provide a better overview: Schematic diagram with partially hidden components.

Make sure that the ground surfaces (2) of the camshafts point up.
Make sure that the rounded surfaces (1) point downwards to the cylinder head.
Check and evaluate the timing once again.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (2) .
Remove the special tool 2 249 117 (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Remove special tool 0 493 882 (11 9 190) (1) .
Release the screw (2) of the belt pulley.
Remove special tool 0 496 366 (11 8 570) (3) .

Courtesy of BMW OF NORTH AMERICA, INC.
Crank the engine on the central bolt twice in a clockwise direction until installation position (1) of the vibration absorber is aligned with the marks of the engine block.

Courtesy of BMW OF NORTH AMERICA, INC.
Position special tool 0 496 366 (11 8 570) (3) on the vibration absorber.
Position the special tool 0 493 882 (11 9 190) (1) in the special tool 0 496 366 (11 8 570) (3) .
The special tool 0 493 882 (11 9 190) (1) must not be inserted very far as it may collide with other components while turning the crankshaft.
Rotate the engine on the central bolt in direction of engine rotation until the special tool aligns with the engine block marks.

Courtesy of BMW OF NORTH AMERICA, INC.
Hand-tighten the special tool 0 496 366 (11 8 570) (3) with a screw (2) of the belt pulley on the vibration absorber.
Slide the crankshaft in the installation position with the special tool 0 493 882 (11 9 190) (1) at the marks and fix it.

Check

Position special tool 2 249 117 (1) on the camshafts of cylinder bank 1.
Check whether the camshafts can be fixed with the special tool 2 249 117 (1) .
Check whether the special tool 2 249 117 (1) can be brought in contact with the cylinder head using 2 screws (2) of the cylinder head cover.

Courtesy of BMW OF NORTH AMERICA, INC.

Result

» The camshafts can be fastened.

Timings are correct.

Measure

Loosen screws (2) .

Remove the special tool 2 249 117 (1) .

Continue the repair in the next step.

Result

» The camshafts cannot be fastened.

Measure

Adjust the timings of cylinder bank 1.

Remove special tool 0 493 882 (11 9 190) (1) .
Release the screw (2) of the belt pulley.
Remove special tool 0 496 366 (11 8 570) (3) .

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (2) .
Remove special tool 2 249 117 (1) .

Courtesy of BMW OF NORTH AMERICA, INC.