Cylinder head cover screw connection cylinder 5 to 8 difficult to access

• The cylinder head cover screws found in the rear area of the cylinder head cover can be secured with a wobble joint (1)  (swivel).

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to FASTENING THE SCREW TO THE HEAT SHIELD AT THE FRONT LEFT .
• Refer to FASTENING THE SCREW ON THE HEAT SHIELD ON THE FRONT RIGHT .
• Refer to INSTALLING THE FRONT HEAT PROTECTION .
• Refer to REPLACING THE SEAL FOR THE EXHAUST GAS TURBOCHARGER .
• Refer to REPLACING THE OIL RETURN LINE .
• Refer to INSTALLING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 1 TO 4 .
• Refer to FASTENING THE BANJO BOLT FOR THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 1 THROUGH 4 .
• Refer to REPLACING THE OIL RETURN LINE .
• Refer to INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
• Refer to SECURING OIL FEED LINE ON EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
• Refer to FASTENING THE BANJO BOLT FOR THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 5 THROUGH 8 .
• Refer to SECURING THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
• Refer to ATTACHING THE OIL SUPPLY LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 1 TO 4 .
• Refer to SECURING OIL FEED LINE ON EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
• Refer to FASTENING THE BANJO BOLT FOR THE COOLANT RETURNING LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 1 THROUGH 4 .
• Refer to SECURING BANJO BOLT OF COOLANT RETURNING LINE ON EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8 .
• Refer to FASTENING THE OIL RETURN LINE ON THE OIL RETURN LID OF CYLINDERS 1 TO 4 .
• Refer to SECURING THE OIL RETURN LINE AT THE OIL RETURN COVER OF THE CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE HEAT SHIELD AT CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 1 TO 4 .
• Refer to HEAT PROTECTION OF THE LEFT-HAND CATALYTIC CONVERTER PIPE .
• Refer to HEAT PROTECTION OF THE RIGHT-HAND CATALYTIC CONVERTER PIPE .
• Refer to INSTALLING UPPER HEAT SHIELD .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
• Refer to INSTALLING THE REAR AXLE COVER .
• Refer to IF INSTALLED: INSTALLING THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
• Refer to INSTALLING THE REAR DIFFUSER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to INSTALLING ENGINE VENTILATION LINE .
• Refer to INSTALLING INTAKE FILTER HOUSING .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to INSTALLING ACOUSTIC COVER .