Refitting sump

• Remove rough seal remains on the sealing surface (1) of the crankcase with the special tool 0 495 102 (11 4 470) .
• Clean the sealing surface (1)  with brake cleaner.

  Courtesy of BMW OF NORTH AMERICA, INC.

  CONSUMABLE DESCRIPTION
  
  

  Brake cleaner 2.0	500 ml, Spray can	83192365214
  	20, Canister	83192365215

  NOTE: TECHNICAL INFORMATION 
  The sealing surfaces must be free of oil, grease and cleaning agents.
• Remove fine seal remains on the sealing surface (1) of the oil pan with the special tool 0 495 102 (11 4 470) .
• Clean the sealing surface (1)  with brake cleaner.

  Courtesy of BMW OF NORTH AMERICA, INC.

  CONSUMABLE DESCRIPTION
  
  

  Brake cleaner 2.0	500 ml, Spray can	83192365214
  	20, Canister	83192365215

• Have the special tool 2 469 803  ready.

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  For additional information see: OVERVIEW OF CONSUMABLES (BMW PARTS CATALOGUE) .
• Position the sealing compound (1)  as shown on the special tool 2 469 803  .

  Parts:  Sealing compound

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: TECHNICAL INFORMATION 
  The processing time of the liquid sealing compound can be at a maximum of 10 min.
  Commissioning of the assembly is not possible until 25 minutes after the processing time.
  Non-observance can lead to leaks in the assembly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Apply a sealing bead (1)  with the sealing compound in the marked  area along the inner edge.
• Completely encircle the oil return orifice (arrow) with the sealing compound.

  The sealant must not enter the oil return orifice.

  SEALING COMPOUND DESCRIPTION
  
  

  Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature

  50 ml, Cartridge

  83190404517

  TECHNICAL DATA SPECIFICATION
  
  

  Height of the sealing bead
  		2.0 mm... 2.5 mm

  NOTE: TECHNICAL INFORMATION 
  The special tool 11 8 780 is only required when the transmission is removed.
• Position the special tool 0 496 120 (11 8 780)  with the transmission bolts (1)  in such a way that the oil pan aligns exactly with the timing case cover.
• Replace the centering sleeves where required.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install oil sump (1)  to top front.
• Tighten all bolts of the oil pan hand-tight, do not tighten completely.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screws (2)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Transmission to oil pan (manual transmission and automatic transmission)
  M8 x 50	Tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach cable in the marked area.
• Connect connector (1)  .
• Tighten down screws (2)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Oil sump to crankcase
  M8 x 110	Tightening torque	24 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screws (1)  .
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Oil sump to crankcase
  M8 x 30	Tightening torque	24 Nm

• Tighten all screws (marks).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Oil sump to crankcase
  M8 x 30	Tightening torque	24 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten all screws (marks).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Oil sump to crankcase
  M8 x 30	Tightening torque	24 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten all screws (marks).

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING STARTER MOTOR .
• Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
• Refer to INSTALLING FRONT AXLE COMPLETELY .
• Refer to TIGHTENING THE SCREWS ON THE LEFT AND RIGHT FRONT AXLE SUPPORT .
• Refer to SECURING THE SPRING STRUT ON THE WISHBONE ON THE BOTTOM LEFT AND RIGHT .
• Refer to SECURING THE WISHBONE ON THE TOP LEFT AND RIGHT ON THE SWIVEL BEARING .
• Refer to REMOVING THE MOBILE LIFTING TABLE .
• Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
• Refer to INSTALLING THE BRAKE CALIPER AT THE FRONT LEFT AND RIGHT .
• Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT TO THE ANTI-ROLL BAR .
• Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
• Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to FASTENING THE WIRING HARNESS OF THE EPS .
• Refer to INSTALLING THE REINFORCEMENT STRUT ON THE ENGINE MOUNT ON THE LEFT AND RIGHT .
• Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
• Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to INSTALLING CLEAN AIR PIPE, TOP .
• Refer to INSTALLING INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to INSTALLING THE SIDE HOOD SEAL ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to FILLING ENGINE OIL .
• Refer to OPENING THE OIL FILLER CAP .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to CHECKING ENGINE OIL LEVEL .
• Refer to INSTALLING REAR UNDERBODY PROTECTION .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .