Installing wiring harness for sensor system of cylinder bank 1
Overview graphic for the wiring harness for the sensor system of cylinder bank 1
- Guide in and position wiring harness for sensor system of cylinder bank 1.
- Connect and lock the plug connections in the arrows area.
- Fasten the wiring harness in the holder (1)
.
- Clip the connector in area (2) into the bracket.
- Tighten the screws in areas (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Wiring harness on crankcase | ||
| M6x16 screw | tightening torque | 10 Nm |
- Connect and lock the plug connections in the arrows area.
- Fix wiring harness mountings (1)
.
- Connect and lock the plug connections in the arrows area.
- Fix wiring harness mountings (1)
.
- Tighten down screw (4) .
TIGHTENING TORQUE SPECIFICATIONS
| Wiring harness to cylinder head cover | ||
| M6x16 screw | tightening torque | 10 Nm |
- Position cable heads (2) at the ground pin.
- Tighten nut (3) .
TIGHTENING TORQUE SPECIFICATIONS
| Ground cable to hold-down device | ||
| Nuts | Tightening torque | 5.5 Nm |
- Secure the wiring harness in area (1) .
- Clip the wiring harness for the sensor system of cylinder bank 1 into the bracket (2) .
- Connect and lock the plug connections (1)
.
- Fix wiring harness mountings (1) .
- Connect and lock the plug connections in the arrows area.
- Fix wiring harness mountings (1) .
- Connect and lock the plug connections in the arrows area.
- Install the foam part (1)
.
- Feed in the wiring harness for the sensor system of cylinder bank 1 (3) downwards at the guide tab (2) .
- Lock the wiring harness for the sensor system of cylinder bank 1 counter to the driving direction at the clamp (1) .
Follow-up work
- Refer to INSTALLING THE RIGHT INTAKE PLENUM .
- Refer to INSTALLING FRONT AXLE COMPLETELY .
- Refer to TIGHTENING THE BOLTS ON THE FRONT AXLE SUPPORT .
- Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
- Refer to ATTACHING THE THERMOSTAT OR TRANSMISSION OIL COOLER LINE ON THE FRONT SUBFRAME .
- Refer to INSTALLING THE UNIVERSAL JOINT .
- Refer to INSTALLING THE OUTPUT SHAFTS .
- Refer to SECURING CABLES ON VERTICAL ACCELERATION SENSOR ON RIGHT AND LEFT .
- Refer to ATTACHING THE CABLE OF THE WHEEL RPM SENSOR ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE BRAKE CALIPER AT THE FRONT LEFT AND RIGHT .
- Refer to SECURING THE RIGHT AND LEFT OUTPUT SHAFTS ON THE WHEEL BEARING .
- Refer to CHECK/ADD FRONT AXLE TRANSMISSION OIL .
- Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
- Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
- Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
- Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
- Refer to INSTALLING THE REINFORCEMENT STRUT ON THE RIGHT ENGINE MOUNT .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
- Refer to REMOVING THE SECURING TOOL OF THE ENGINE IN INSTALLATION POSITION .
- Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
- Refer to SECURING THE AIR SUSPENSIONS STRUTS IN THE FRONT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to INSTALLING THE LATERAL HOOD SEALS .
- Refer to INSTALLING THE MOUNT OF THE HOOD SEAL .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to CHECKING THE STRAIGHT-AHEAD DRIVING POSITION OF THE STEERING WHEEL .
- Refer to CHECKING THE AIRBAG FOR FUNCTION .