Installing the ignition coil of cylinder bank 1

Precondition

Ignition is switched off.

NOTE: RISK OF DAMAGE
Damage to the ignition coil.
The silicone hose of the ignition coil must not be contaminated by fuel as this can lead to failure of the ignition coil.

When working on the fuel system, cover the ignition coils with suitable materials and remove where required.
Do not oil or grease the silicone tube of the spark plug socket. Do not use any protection or maintenance products (e.g. silicone spray, rubber care products, rust remover, etc.).

NOTE: The description is provided only at one component. The procedure is the same for all other components.

Insert and install the ignition coil (2) .
Tighten down screw (1) .

TIGHTENING TORQUE SPECIFICATIONS

Ignition coil
screw	Tightening torque	8 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Feed in and install the cable clip (2) .
Tighten the screws (1) .

TIGHTENING TORQUE SPECIFICATIONS

Wiring harness on the cylinder head cover
M6x16 screw	Tightening torque	10 Nm
Nut M6	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect and lock connectors (arrows).
The connectors (arrows) must audibly engage.
Guide in and install cover (2) .
Insert and install cable (1) .
Secure the clamps (arrows).

Courtesy of BMW OF NORTH AMERICA, INC.

Installing control unit holder for cylinders 1 to 4

NOTE: RISK OF DAMAGE
Electrostatic discharge.
Damage to or destruction of electrical components.

Leave the electrical components in their original packaging until they are being installed. Only use the original packaging for returning the product. Always package removed components straight away.
Read and comply with user information on using the associated special tool 12 7 060.
Only tap the housings of electrical components. Do not tap pins or multi-pin connectors directly.
Wear electrically conductive clothing and antistatic shoes (with ESD symbol).
For additional information see: NOTES ON ESD (ELECTROSTATIC DISCHARGE) PROTECTION .

NOTE: TECHNICAL INFORMATION
Follow instructions for removing and installing control units.
For additional information see: INSTRUCTIONS FOR REMOVAL AND REPLACEMENT OF CONTROL UNITS .

NOTE: TECHNICAL INFORMATION
If control units are disconnected, fault memory entries and functional limitations may occur.
The fault memory entries must be read out and, if necessary, deleted.

Feed in the control unit bracket (1) with the DME control unit in the brackets (2) and install.

Courtesy of BMW OF NORTH AMERICA, INC.
Lock the control unit holder (1) on the retaining tabs (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Connect the connector (3) with bracket (4) and lock.
The connector (3) must engage audibly.
Connect connectors (2) and lock.
The connector (2) must engage audibly.
Connect all connectors (1) and lock.
The connectors (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Fasten the clamps (arrows) to the control unit bracket (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Feed in and install the control unit bracket (2) with control unit.
Tighten the screws (1) .

TIGHTENING TORQUE SPECIFICATIONS

Control unit holder
Hexagon screw	Tightening torque	8 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Fasten the clamps (3) on the bracket (4) .
Connect connectors (2) and lock.
The connectors (2) must engage audibly.
Connect connectors (1) and lock.
The connectors (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.

Installing the cover of the right DME control unit

Feed in the cover (1) in the guides and install it.

Courtesy of BMW OF NORTH AMERICA, INC.