Remove automatic transmission (GA8HP50Z)

Preliminary work

Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
Refer to IF THE ACTIVE STABILIZER IS INSTALLED: REMOVING FAN COWL .
Refer to REMOVING REAR UNDERBODY PROTECTION .
Refer to REMOVING THE CENTER UNDERBODY PROTECTION .
Refer to REMOVING THE UNDERBODY PLANKING OF THE TRANSMISSION ON THE SIDE .
Refer to REMOVING THE CONNECTING SUPPORT FROM THE TUNNEL .
Refer to REMOVING THE REAR AXLE COVER .
Refer to IF INSTALLED: REMOVING THE TORSION STRUT ON THE RIGHT AND LEFT WHERE REQUIRED .
Refer to REMOVING THE REAR DIFFUSER .
Refer to REMOVING COMPLETE EXHAUST SYSTEM .
Refer to REMOVING THE HEAT SHIELDS .
Refer to REMOVING THE RETAINING PLATES .
Refer to REMOVING TRANSMISSION CROSS-MEMBER .
Refer to PARTIALLY LOOSENING THE PROP SHAFT .

CAUTION: Materials harmful to health.
Contact with fluids harmful to health!

Note and follow safety instructions on containers.
Conduct all work in appropriate personal protective equipment only.

NOTE: RISK OF DAMAGE
Damage to the engine block.
Serious damage to the engine block and transmission due to damaged and corroded screws.

It is imperative that protruding threads of the transmission bolts are checked for corrosion and damage prior to removal.
It is imperative that all rust is removed from corroded threads and that they are cleaned prior to removal.
Replace rusted and damaged bolts.

NOTE: RISK OF DAMAGE
Damage of components in the engine compartment.
When removing the transmission, the tilting of the engine may cause damage to components in the engine compartment.

Before removing the transmission: Support the engine.
Protect engine from tipping movements.
Follow the specifications in the repair instructions.

NOTE: RISK OF DAMAGE
Damage to the transmission.
Damage to the transmission due to unapproved transmission oil.

Use only the approved transmission oil.
Check the transmission oil level after completing the repair.

Support transmission.

Support the transmission with special tools 0 495 498 (23 4 050) and 2 219 012 .

NOTE: TECHNICAL INFORMATION
Notes on universal transmission support are a fundamental requirement for these repair instructions and must be complied with at all times.
For additional information see: UNIVERSAL BMW TRANSMISSION SUPPORT .

Courtesy of BMW OF NORTH AMERICA, INC.

Secure transmission to mounting with tensioning strap (1).

REMOVING EXHAUST SYSTEM holder

Loosen nuts (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Remove the exhaust bracket (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Detching the ground strap from the transmission

Release the screw (1) and release the ground strap (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Disconnect hydraulic lines on the transmission

Loosen screw (1).
Disconnect hydraulic lines (2) to transmission oil cooler.

Courtesy of BMW OF NORTH AMERICA, INC.

Removing the acoustic cover

Pull the expanding rivet (1) off.
Remove the acoustic cover (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Release converter bolt

Turn the engine on the vibration damper with the special tool 0 493 380 (11 6 480) in the direction of rotation until the bolt (1) becomes visible in the recess.
Release all 6 screws (1) the torque converter.

Courtesy of BMW OF NORTH AMERICA, INC.

Securing the torque converter

Prepare the special tool 0 494 478 (24 4 161) (1) with the special tool 0 494 965 (24 4 165) (2) as shown.

Courtesy of BMW OF NORTH AMERICA, INC.
Remove sealing cap (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Insert special tool 0 494 451 (24 4 160) into the recess of the transmission housing and apply slight tension using the screw (1).
Screw the bolt (2) in to the stop.
Tighten down screw (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Disconnecting the connector from the sealing sleeve

NOTE: TECHNICAL INFORMATION
Notes on mechatronics are a fundamental requirement for these repair instructions and must be complied with at all times.
For additional information see the Notes on mechatronics below.

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock the connector (1) by turning and disconnect.
Do not touch pins.
Loosen all cable clips.
Insert the special tool 0 494 213 (24 2 390) in the sealing sleeve (1) in arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.

Notes on mechatronics

CAUTION: Materials harmful to health.
Contact with fluids harmful to health!

Note and follow safety instructions on containers.
Conduct all work in appropriate personal protective equipment only.

NOTE: RISK OF DAMAGE
Damage to the automatic transmission after removal of the mechatronics.
Serious damage to the automatic transmission due to non-compliance with the following tasks:

Load specific data status with the diagnostic system.
Use only approved transmission oil.
After completion of repair work, check the transmission oil level.

NOTE: RISK OF DAMAGE
Electrostatic discharge.
Damage to or destruction of electrical components.

Leave the electrical components in their original packaging until they are being installed. Only use the original packaging for returning the product. Always package removed components straight away.
Read and comply with user information on using the associated special tool 12 7 060.
Only tap the housings of electrical components. Do not tap pins or multi-pin connectors directly.
Wear electrically conductive clothing and antistatic shoes (with ESD symbol).
For additional information see: NOTES ON ESD (ELECTROSTATIC DISCHARGE) PROTECTION .

Unscrew the transmission bolts

Support the engine.
Release the remaining six transmission bolts (arrows) and remove the transmission.

Courtesy of BMW OF NORTH AMERICA, INC.