Secure the central screw of the variable exhaust camshaft timing control (cylinders 1 to 6)
WARNING: This page does not describe the selected car, but rather 30 other vehicles, including the 2022 BMW M760i xDrive, 2022 BMW 750i xDrive, 2022 BMW 745e xDrive, 2022 BMW 740i, and 2021 BMW M760i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
- Tighten the central bolt (1) on the exhaust camshaft adjuster with an electronic torque/torsion angle wrench (2) .
TIGHTENING TORQUE SPECIFICATIONS
| Variable camshaft timing control central bolt to camshaft | ||
|---|---|---|
| M10x1 Replace screws and grease contact surface with copper paste. |
1. Joining torque | 30 Nm |
| 2. Angle of rotation | 90° | |
Follow-up work
- Refer to REMOVING THE SPECIAL TOOLS TO FIX THE CAMSHAFTS .
- Refer to CHECKING TIMING .
- Refer to REMOVING THE SPECIAL TOOLS TO DISCONNECTING THE CRANKSHAFT .
- Refer to INSTALLING THE BELT PULLEY .
- Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR .
- Refer to INSTALLING THE DRIVE BELT FOR ALTERNATOR 2 AND THE AIR CONDITIONING COMPRESSOR .
- Refer to REMOVING THE PROTECTIVE PLATE AT THE RADIATOR .
- Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN .
- Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER .
- Refer to INSTALLING THE TIMING CASE COVER AT THE TOP FOR CYLINDERS 1 TO 6 .
- Refer to INSTALLING BOTH SOLENOID VALVES ON THE RIGHT .
- Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to INSTALLING THE CYLINDER HEAD COVER ON THE RIGHT .
- Refer to FASTENING THE COOLANT FEED LINE FOR THE RIGHT EXHAUST TURBOCHARGER .
- Refer to CONNECTING THE COOLANT HOSE TO THE RADIATOR .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
- Refer to PREPARING THE INJECTOR FOR INSTALLATION .
- Refer to INSTALLING INJECTORS .
- Refer to INSTALLING RIGHT HIGH PRESSURE PUMP .
- Refer to INSTALLING THE RIGHT HIGH-PRESSURE RAIL .
- Refer to INSTALLING ALL HIGH PRESSURE LINES BETWEEN THE RAIL AND THE INJECTORS .
- Refer to INSTALLING FUEL DELIVERY LINE .
- Refer to INSTALLING THE HIGH-PRESSURE LINE ON THE RIGHT BETWEEN THE HIGH-PRESSURE PUMP AND THE HIGH-PRESSURE RAIL .
- Refer to INSTALLING THE RIGHT-HAND CHARGE AIR PIPE .
- Refer to INSTALLING TOP RIGHT CLEAN AIR PIPE .
- Refer to PARTIALLY FASTENING THE WIRING HARNESS ON THE RIGHT CYLINDER HEAD COVER .
- Refer to CONNECTING ALL THE CONNECTORS TO THE DME CONTROL UNIT FOR CYLINDERS 1 TO 6 AND TO THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING COVER FOR THE RIGHT DME CONTROL UNIT .
- Refer to INSTALLING THE IGNITION COILS .
- Refer to INSTALLING THE RIGHT-HAND VENTILATION LINE .
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to INSTALLING THE TANK VENT LINE .
- Refer to INSTALLING THE ENGINE VENTILATION LINE ON THE INTAKE SYSTEM .
- Refer to MOUNTING THE LEFT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING THE LEFT THROTTLE BODY .
- Refer to MOUNTING THE RIGHT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING THE RIGHT THROTTLE BODY .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING FAN COWL .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING LEFT INTAKE PORT .
- Refer to INSTALLING THE LEFT-HAND AIR DUCT .
- Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
- Refer to INSTALLING RIGHT AIR DUCT .
- Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
- Refer to INSTALLING FANFARE HORN, RIGHT .
- Refer to INSTALLING THE FANFARE ON THE LEFT SIDE .
- Refer to INSTALLING THE CENTER TOP CROSS CONNECTION .
- Refer to INSTALLING BOTH HEADLIGHTS .
- Refer to INSTALLING BUMPER COVER, FRONT .
- Refer to INSTALLING FRONT SECTION OF THE FRONT WHEEL ARCH COVER (PARTIALLY REMOVED) .
- Refer to INSTALLING FRONT ORNAMENTAL GRILLE .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to CHECKING THE COOLANT LEVEL IN THE LOW-TEMPERATURE COOLANT CIRCUIT AND TOPPING UP, IF NEEDED .
- Refer to FILLING THE COOLING SYSTEM WITH THE VACUUM FILLING UNIT .
- Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
- Refer to ADJUSTING HEADLIGHTS .