If installed: Removing strut brace in the rear of the engine compartment

NOTE: TECHNICAL INFORMATION
Driving without the strut brace/front-end strut or tension strut is not permitted.

Removing left and right wiper arm

NOTE: Description is for left component only. Procedure on the right side is identical.

Removing wiper arm

NOTE: RISK OF DAMAGE
Damage to the wiper console.
If the wiper arm is removed without a special tool, the wiper console can break.

Only remove the wiper arm with the described special tool.
Do not lever off the wiper arm, as otherwise the wiper console can break at the predetermined breaking point for active pedestrian protection.

Disconnect the washer fluid hose (1) at the separation point and feed out from the windshield panel guide.

Courtesy of BMW OF NORTH AMERICA, INC.
Remove the protective cap (1).
Loosen nut (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Detach wiper arm (1) with special tool 0 493 441 (61 6 060) .

Courtesy of BMW OF NORTH AMERICA, INC.

Remove windshield panel cover

Release snap fastener (1) of the washer fluid hose (2) and put the washer fluid hose (2) to one side.
Unclip the clips (3) on the windshield panel cover (4).

Courtesy of BMW OF NORTH AMERICA, INC.
Beginning from the side, pull up windshield panel cover (1) out of the detent (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Removing trailing link at spring bolt

NOTE: TECHNICAL INFORMATION
Driving without the strut brace/front-end strut or tension strut is not permitted.

Version A:
Loosen screws (1) and (2).
Remove tension strut (3) at the shock tower upwards.

Courtesy of BMW OF NORTH AMERICA, INC.
Version B:
Loosen screws (1) and (2).
Remove tension strut (3) at the shock tower upwards.

Courtesy of BMW OF NORTH AMERICA, INC.

Install tension strut on shock tower

NOTE: TECHNICAL INFORMATION
Driving without the strut brace/front-end strut or tension strut is not permitted.

Version A:
Install the tension strut (3) on the shock tower.
Tighten down screws (1).

TIGHTENING TORQUE SPECIFICATION

Tension strut on firewall
M10x25 screw	Tightening torque	56 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Replace screws (2).
Parts: Screws
Tighten down screws (2).

TIGHTENING TORQUE SPECIFICATION

Tension strut to shock tower
screw Replace screws.	Joining torque	56 Nm
	Angle of rotation	90°

Version B:
Install tension strut (3) on the shock tower.
Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATION

Tension strut on firewall
M10x25 screw	Tightening torque	56 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Replace the screw (2).
Parts: Screw
Tighten down screw (2).

TIGHTENING TORQUE SPECIFICATION

Tension strut to shock tower
screw Replace screws.	Joining torque	56 Nm
	Angle of rotation	90°

Installing windshield panel cover

NOTE: RISK OF DAMAGE
Damage caused by water ingress into the vehicle.
Water ingress into the vehicle may result in damage to components, malfunctions and corrosion.

Ensure correct installation of the components.
Only use undamaged components.

NOTE: TECHNICAL INFORMATION
Before installing the cowl cover, it is imperative to check the correct routing and firm fit of the 48V line.
An incorrectly laid or attached 48V line can be damaged by the wiper kinematics.

Press the cowl cover (1) into the detent (2) beginning from the side.

Courtesy of BMW OF NORTH AMERICA, INC.
Clip in the cowl cover (4) with the detents (3).
Position the washer fluid hose (2) and connect the snap fastener of the washer fluid hose (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Install left and right wiper arm

NOTE: Description is for left component only. Procedure on the right side is identical.

Installing left and right wiper arm

NOTE: TECHNICAL INFORMATION
The window wiper system must be in the zero position.
After installing the cowl cover and before installing the wiper arms:
Operate the window wiper system one time, to ensure the window wiper system has the correct installation position.

Connect the wiper arm (3).
Correctly position the wiper arm (2) in relation to the window edge (1).

TECHNICAL DATA SPECIFICATION

Distance from window pane edge to wiper blade
	Wiper arm right (A)	57.5 ± 5 mm
	Wiper arm left (B)	63.3 ± 4 mm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (2).

TIGHTENING TORQUE SPECIFICATION

Windshield wiper arm
Combination hexagon nut	tightening torque	35 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect the protective cap (1).
Feed the washer fluid hose (1) into the guide of the windshield panel and connection at the separation point.

Courtesy of BMW OF NORTH AMERICA, INC.