Only on vehicles with active pedestrian protection
WARNING:
Pyrotechnic components.
Danger! Immobilization period-threatening injuries!
Danger! Immobilization period-threatening injuries!
- All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.
- Replace any damaged part or ones that have been dropped.
- For additional information see: SAFETY REGULATIONS FOR HANDLING COMPONENTS WITH GAS GENERATORS .
Deactivating the 48 V electrical system
Precondition
Ignition is switched off.
WARNING:
Deactivate the 12-V electrical system.
Risk of short circuits! Risk of fire!
Risk of short circuits! Risk of fire!
- Make sure that there is no battery charger connected to the jump start terminal in the engine compartment.
- For vehicles with additional electrical systems (48 V electrical system, high-voltage vehicle electrical system), this absolutely must be deactivated before the vehicle battery is disconnected.
WARNING:
Deactivate the 48-V electrical system.
Risk of short circuits! Risk of fire!
Risk of short circuits! Risk of fire!
- Make sure that there is no charger connected to the jump start terminal in the engine compartment.
NOTE:
RISK OF DAMAGE
Damage to the 48-V battery
If a 48-V battery that is disconnected from the electrical system is activated, the battery electronics will be damaged.
Damage to the 48-V battery
If a 48-V battery that is disconnected from the electrical system is activated, the battery electronics will be damaged.
- Only ever activate the 48 V electrical system when the 48 V battery is fully connected up.
NOTE:
TECHNICAL INFORMATION
Observe notes on the 48-V battery. See NOTES ON THE 48-V BATTERY .
Observe notes on the 48-V battery. See NOTES ON THE 48-V BATTERY .
- Deactivate the 48 V electrical system by opening the hood.
Deactivation is automatic.
Check
NOTE:
TECHNICAL INFORMATION
Zero voltage (48 V electrical system switched-off) is only displayed in PAD mode.
Zero voltage (48 V electrical system switched-off) is only displayed in PAD mode.
- Press the START-STOPPING button quickly 3 times without stepping on the brake pedal to establish the PAD mode.
- Check the de-energized state in the instrument cluster (KOMBI) in the PAD mode.
Desired state
- The Check Control message "48 V electrical system." switched off is displayed.
Result
» Absence of voltage cannot be specified with the Check Control message "48 V electrical system switched off." (1). Work start is not permitted.
Measure
- Repeat the "deactivate 48 V electrical system" service function.
- Vehicle management > service function > voltage supply > deactivate 48 V electrical system
Only if the Check Control message "48 V electrical system switched off." is displayed in the instrument cluster (KOMBI), the 12V battery may be disconnected.
Contact the technical support if the absence of voltage is not clearly given.
Result
» The Check Control message reports that 48 V electrical system is switched off.
Measure
- Exit PAD mode by pressing the START-STOPPING button once without stepping on the brake pedal.
"Disconnect the negative battery cable of the 48-V battery" work can be started.
- Unlock and disconnect the CAN bus plug connection of the gear sensor.
- Release the clip.
- Loosen nut.
- Detach the negative battery cable of the 48-V battery from the negative battery terminal, set to one side and secure.WARNING: Unprotected battery terminals.
Risk of short circuits! Risk of fire!- Cover the vehicle battery.
- Cover the vehicle battery with the special tool 2 452 007 as shown.
- Position the battery ground lead as shown.
Deactivate electrical system
NOTE:
TECHNICAL INFORMATION
The vehicle-specific specifications described in the further information must be followed!
The vehicle-specific specifications described in the further information must be followed!
- Deactivate the vehicle electrical system according to the specifications described in the following information.
Activate electrical system
NOTE:
TECHNICAL INFORMATION
The vehicle-specific specifications described in the further information must be followed!
The vehicle-specific specifications described in the further information must be followed!
- Activate the vehicle electrical system according to the specifications described in the following information.
Activating the 48 V electrical system
Precondition
Ignition is switched off.
NOTE:
RISK OF DAMAGE
Damage to the 48-V battery
If a 48-V battery that is disconnected from the electrical system is activated, the battery electronics will be damaged.
Damage to the 48-V battery
If a 48-V battery that is disconnected from the electrical system is activated, the battery electronics will be damaged.
- Only ever activate the 48 V electrical system when the 48 V battery is fully connected up.
- Raise the battery ground cable.
- Remove special tool 2 452 007.
- Release the negative battery cable of the 48-V battery from the attachment.
- Position the negative battery cable of the 48-V battery on the negative battery terminal.
- Tighten nut.TIGHTENING TORQUE SPECIFICATION
Negative battery cable to 48-V battery Nut M8 tightening torque 19 Nm - Connect the connector of the CAN bus and lock it.
- Clip in clip.
- Activate the 48 V electrical system by closing the hood.
Activation is automatic.