Install Engine Mount In Front Of Cowling With Wheel Arch

• Preclean all bonding surfaces with solvent cleaner R2.
  CONSUMABLE SPECIFICATION
  
  

  Cleaning agent R2

  500 ml

  83190417324

• Clean all bonding surfaces with solvent cleaner R1.
  CONSUMABLE SPECIFICATION
  
  

  Cleaning agent R1

  100 ml, Bottle

  83192211217

• Apply adhesive K1 to bonding surfaces.
  ADHESIVE SPECIFICATION
  
  

  Body adhesive K1

  195 ml

  83190413015

• During installation of the new parts, make sure that sufficient adhesive has been applied to all bonding surfaces.
• Install the new part with an alignment bracket or a universal fixture.
• Rivet the new parts in the areas (1) with three blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the new part in the area (1) and (2) with blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install new part and rivet in area (1) with blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

• Rivet the new parts in the area (2) with blind rivet N2.

  Courtesy of BMW OF NORTH AMERICA, INC.

  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N2  Ø 6.5 mm; clamping area 4.8-6.8 mm

  83190301419

• Weld the new part in the areas (3).

  Avoid excessive application of heat to adhesive areas.

• Weld the new part in the area (1).

  Avoid excessive application of heat in this process.

  The cowling cross-member (2) is filled with hardly inflammable cavity foam.

• In case of smoke formation: Stop the welding procedure and cool the welded area with compressed air if applicable.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the new part in the areas (1) and (2) with blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the new part in the areas (1) with blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the new part in the areas (1) with blind rivets N1.
  CONSUMABLE SPECIFICATION
  
  

  Blind rivet N1  Ø 6.5 mm; clamping area 2.8-4.8 mm

  83190301414

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install the reinforcement plates (1) and attach by welding.
• Observe the bonding surface (2) of the aluminum spring support.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install the new part section and weld it in the areas (1) to (3).
• While doing so, observe the adhesive area (4) of the aluminum spring support.

  Avoid applying too much heat to adjacent adhesive area (4).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install an EMC screw in area (1).
  CONSUMABLE SPECIFICATION
  
  

  screw  EMC screw, SF Plus, M5x15

  83190301639

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install an EMC screw in area (1).
  CONSUMABLE SPECIFICATION
  
  

  screw  EMC screw, SF Plus, M5x15

  83190301639

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work