Install the wiring harness section of the transmission wiring harness
Wiring harness section of transmission wiring harness
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
- Route all cables without abrasions, do not trap and crush.
- Insert and install the wiring harness (1) for the transmission module.
- Feed in and install the wiring harness section (2) of the transmission wiring harness.
- Secure clamps (1).
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Thread in the wiring harness section (2) of the supply module and install.
- Secure clamp (arrow).
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
Fastening the transmission
- Move the transmission (3) to the installation position.
- Replace screws (2).
Parts: Screws
- Tighten down screws (2).TIGHTENING TORQUES SPECIFICATION
Transmission cross member to body M8 tightening torque 19 Nm - Secure the cable with the clamp (1).
- Loosening the luggage strap (1).
- Remove special tools 2 219 012
and 0495 498 (23 4 050)
.
- Secure clamps (2).
- Connect connectors (1) and lock. The connector (1) must engage audibly.
- Feed in and install the wiring harness section (1) of the transmission wiring harness.
- Secure the clamps (arrows).
- Feed in and install the wiring harness section (3) of the transmission wiring harness.
- Make sure that the lock (2) engages correctly.
- Tighten down screws (1).TIGHTENING TORQUES SPECIFICATION
Cable bracket on rear cylinder head/transmission M6x20 tightening torque 8 Nm - Secure the clamps (arrows).
- Insert the cable bracket (2) in the arrow direction and install it.
The lock (1) must engage audibly.
- Guide in and lock cable clip (3).
The cable clip (3) must engage audibly.
- Insert the cable bracket (2) in the arrow direction and install it.
The locks (1) must engage audibly.
Follow-up work
- Refer to INSTALLING TRANSMISSION MOUNTING BRACKET (ALL-WHEEL DRIVE VEHICLE) .
- Refer to INSTALLING THE TRANSMISSION BEARING SUPPORT .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING THE RETAINING PLATE AND HEAT SHIELD .
- Refer to SECURING UNDERBODY PANELING ON LEFT AND RIGHT SIDE .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING CENTER STIFFENING PLATE .
- Refer to IF INSTALLED: INSTALL THE RIGHT AND LEFT TORSION STRUTS .
- Refer to INSTALLING TANK COVER ON LEFT AND RIGHT .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING CONTROL UNIT BRACKET .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING COVER OF THE DME CONTROL UNIT .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING THE STRUT BRACE .
- Refer to INSTALLING THE SECOND END PANEL UNDERNEATH .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .