Insert the exhaust turbocharger for the cylinders 5 to 8

WARNING: Hot surfaces.
Risk of burning!

Perform all work only on components that have cooled down.

CAUTION: Heavy component.
Heavy components can lead to injury or damage.

Remove and install heavy components with the aid of another person/other persons.

NOTE: RISK OF DAMAGE
Electrostatic discharge.
Damage to or destruction of electrical components.

Leave the electrical components in their original packaging until they are being installed. Only use the original packaging for returning the product. Always package removed components straight away.
Read and comply with user information on using the associated special tool 12 7 060.
Only tap the housings of electrical components. Do not tap pins or multi-pin connectors directly.
Wear electrically conductive clothing and antistatic shoes (with ESD symbol).
For additional information see: NOTES ON ESD (ELECTROSTATIC DISCHARGE) PROTECTION .

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

NOTE: TECHNICAL INFORMATION
If the exhaust turbocharger is damaged, it is imperative to observe the additional information.

NOTE: TECHNICAL INFORMATION
For exhaust turbocharger damage: Check the pressure pipes, charge air cooler and intake plenum for foreign matter, damage and correct functionality.
If the oil return line is exchanged, then the connecting pipe to the oil sump must ALWAYS be cleaned, as the connecting pipe can coke.

NOTE: TECHNICAL INFORMATION
Prior to replacing the exhaust turbocharger: Observe the notes on troubleshooting on the exhaust turbocharger.

Prepare for the installation of the exhaust turbocharger

Check the oil feed lines and oil return lines for contamination or obstruction, clean or replace if necessary.
If the oil feed lines or oil return lines are heavily contaminated, it is recommended that the engine oil and oil filter are changed.
If installed: Check the coolant feed lines and coolant return lines for the exhaust turbocharger for contamination or obstruction and clean or replace as needed.
Check the screw connections and plug connections of all lines for accuracy.
Check air cleaner for contamination and clean or replace as needed.
Check correct functioning of crankcase ventilation.
Replace all gaskets.

Parts: Seals

Replace the seal (1).
Parts: Seal
Check the pin (arrow) for damage, replace exhaust manifold if necessary.

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure that the O-ring (1) does not fall into the oil duct in the engine block.
Replace O-ring (1).
Parts: O-ring

If the O-ring (1) cannot be disassembled, the oil return lid must be disassembled.
Coat O-ring (1) with engine oil.

ENGINE OIL DESCRIPTION

Technically suitable engine oils for BMW Group engines

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen screws (2).
Remove the oil return line (1).
Ensure that the sealing surfaces in the area of the oil return line are planar and free from oil and grease.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace oil return line (3) after each disassembly of the exhaust turbocharger.
Parts: Oil return line
Replace the seal (1).
Parts: Seal
Replace screws (2).
Parts: Screws
Position screws (2) in oil return line (3).
Position the seal (1) on the screws (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Position the oil return line (1).
Screws (2) must be tightened with the aid of an support person.

TIGHTENING TORQUE SPECIFICATIONS

Oil return line at the exhaust turbocharger
M6x16 Replace screws.	Joining torque	5 Nm
M6x16 Replace screws.	Angle of rotation	60°

Courtesy of BMW OF NORTH AMERICA, INC.

Feed in and install the exhaust turbocharger (2) at left with the coolant lines and oil return line.
During installation of the right exhaust turbocharger (2), make sure that the oil return line is correctly positioned in the oil return cover.
Connect connectors (1) and lock.
The connector (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace the V-clip (2).
Parts: V-band clamp
Position V-clip (2).
Tighten down screw (1).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUE SPECIFICATIONS

Exhaust turbocharger to exhaust manifold
V-band clamp Replace V-band clamp.	Tightening torque	20 Nm

Tighten the screw (1) on the oil return pipe (2).

TIGHTENING TORQUE SPECIFICATIONS

Oil return line to oil return cover
M6	tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Feed the coolant return line (2) above the coolant feed line (3).
Connect plug connection (1) and lock.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace sealing ring (1) of the coolant line (2).
Parts: Sealing ring

Courtesy of BMW OF NORTH AMERICA, INC.
Connect coolant lines (4).
Connect coolant lines (3).
Tighten down screws (2).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUE SPECIFICATIONS

Coolant line from exhaust turbocharger to bracket
M6x30	tightening torque	8 Nm

Remove the lint-free rag (1).
Replace the screw (1).
Parts: Screw
Replace the sealing ring or sealing rings (2).
Parts: Sealing ring or sealing rings
Make sure that when installing sealing rings without a fitting aid (bridge), both sealing rings are replaced.
Position screw (1) with the sealing ring or sealing rings (2) on the oil feed line.

Courtesy of BMW OF NORTH AMERICA, INC.
Position oil feed line.
Screw in the banjo bolt (2) several threads.
Hand-tighten the bolt (1).
Tighten the banjo bolt (2).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUE SPECIFICATIONS

Banjo bolt for oil feed line to exhaust turbocharger
M10x1 Replace the screw and sealing rings.	Joining torque	8 Nm
M10x1 Replace the screw and sealing rings.	Angle of rotation	70°

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Oil feed line to exhaust turbocharger
M6x16	tightening torque	10 Nm

Determining the screw type and selecting the appropriate socket wrench:

Screw type	Matching socket wrench
Hexagon screw (3)	Commercial socket wrench (1)
Multi-tooth screw (4)	Multi-tooth socket wrench (2)

Courtesy of BMW OF NORTH AMERICA, INC.

Position the retaining plate (2).
Secure the wiring harness (1) on the retaining plate (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Position the retaining plate (2).
Tighten down screws (2).

TIGHTENING TORQUE SPECIFICATIONS

Holder control sensor cable to the cylinder head cover
M6x16	tightening torque	8 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect plug connection (3) and lock.
Position union nut (2) and turn it a few times.
Position screw (1) and turn it a few times.
Tighten union nut (2).

TIGHTENING TORQUE SPECIFICATIONS

Fuel delivery line to high pressure pump
M14	Tightening torque	30 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screw (1).

TIGHTENING TORQUE SPECIFICATIONS

Fuel supply line to cylinder head cover/cylinder head
M6x16	tightening torque	10 Nm

Connect connectors (1) and lock.

Courtesy of BMW OF NORTH AMERICA, INC.
Connect connectors (1) and lock.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
Refer to INSTALLING THE LEFT CHARGE AIR LINE .
Refer to CLOSING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
Refer to INSTALLING THE FRONT LEFT BOTTOM WHEEL ARCH COVER .
Refer to INSTALLING THE FRONT BOTTOM RIGHT WHEEL ARCH COVER .
Refer to INSTALLING FAN COWL .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to INSTALLING FRONT CROSS CONNECTION (FRONT-END STRUT REMOVED) .
Refer to INSTALLING BOTH FRONT-END STRUTS .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 5 TO 8 .
Refer to RELEASING THE HEAT SHIELD .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING RIGHT HEAT SHIELD .
Refer to INSTALLING LEFT HEAT SHIELD .
Refer to INSTALLING HEAT SHIELD, TOP .
Refer to INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
Refer to INSTALLING THE LEFT OXYGEN SENSOR MONITOR .
Refer to PARTIALLY INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
Refer to PARTIALLY INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE RETAINING BRIDGE .
Refer to INSTALLING EXHAUST SYSTEM .
Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
Refer to IF INSTALLED: INSTALLING THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
Refer to INSTALLING THE REAR DIFFUSER .