Replace the seal for the exhaust gas turbocharger
- Replace sealing ring (1).
Parts : Sealing ring
- Insert sealing ring. Whilst doing this, pay attention to the pin (arrow).
Follow-up work
- Refer to INSTALLING THE FRONT HEAT PROTECTION .
- Refer to FASTENING THE SCREW TO THE HEAT SHIELD AT THE FRONT LEFT .
- Refer to FASTENING THE SCREW ON THE HEAT SHIELD ON THE FRONT RIGHT .
- Refer to INSTALLING THE ALTERNATOR .
- Refer to PUTTING ON THE DRIVE BELT .
- Refer to REMOVING SPECIAL TOOL ON BELT TENSIONER .
- Refer to REPLACING THE OIL RETURN LINE .
- Refer to INSTALLING EXHAUST TURBOCHARGER FOR CYLINDER 1 TO 4 .
- Refer to FASTENING THE BANJO BOLT FOR THE COOLANT FEED LINE TO THE EXHAUST TURBOCHARGER OF THE CYLINDERS 1 TO 4 .
- Refer to FASTENING THE COOLANT FEED LINE AT THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 1 TO 4 .
- Refer to FASTENING THE BANJO BOLT FOR THE COOLANT RETURN LINE ON THE EXHAUST TURBOCHARGER OF THE CYLINDERS 1 TO 4 .
- Refer to ATTACHING THE OIL SUPPLY LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 1 TO 4 .
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Oil feed line to exhaust turbocharger M6x16 Tightening torque 10 Nm - Refer to FASTENING THE OIL RETURN LINE ON THE OIL RETURN LID OF CYLINDERS 1 TO 4 .
- Refer to INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
- Refer to SECURING THE OIL RETURN LINE AT THE OIL RETURN COVER OF THE CYLINDERS 5 TO 8 .
- Refer to SECURING THE BANJO BOLT FOR THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8 .
- Refer to SECURING THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
- Refer to SECURING OIL FEED LINE ON EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Oil feed line to exhaust turbocharger M6x16 Tightening torque 10 Nm - Refer to HEAT PROTECTION OF THE LEFT-HAND CATALYTIC CONVERTER PIPE .
- Refer to HEAT PROTECTION OF THE RIGHT-HAND CATALYTIC CONVERTER PIPE .
- Refer to INSTALLING UPPER HEAT SHIELD .
- Refer to IF INSTALLED: INSTALL THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING THE RIGHT UNFILTERED-AIR DUCT .
- Refer to INSTALLING THE LEFT UNFILTERED-AIR DUCT .
- Refer to INSTALLING LEFT CLEAN AIR PIPE .
- Refer to INSTALLING RIGHT CLEAN AIR PIPE .
- Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR AND THE MONITORING OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR AND THE MONITORING OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING ENGINE VENTILATION LINE .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING FAN COWL .
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
- Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .