Install the wiring harness section of the transmission wiring harness
Wiring harness section of transmission wiring harness
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
- Route all cables without abrasions, do not trap and crush.
- Insert and install the wiring harness (1) for the transmission module.
- Guide in the wiring harness section of the transmission wiring harness and install.
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Cable bracket on rear cylinder head/transmission M6 x 20 tightening torque 8 Nm - Connect connector (2) and lock audibly.
- Connect connector (3) and lock audibly.
- Connect connector (4) and lock audibly.
Fastening the transmission
- Move the transmission (3) to the installation position.
- Replace screws (2).
Parts: Screws
- Tighten down screws (2).TIGHTENING TORQUES SPECIFICATION
Transmission cross member to body M8 tightening torque 19 Nm - Secure the cable with the clamp (1).
- Loosening the luggage strap (1).
- Remove special tools 2 219 012 and 0 495 498 (23 4 050) .
- Feed in and install the wiring harness section (1) of the transmission wiring harness.
- Secure the cable with the clamps (arrows).
- Secure the cable with the clamps (arrows).
- Connect the connector (1) to the starter and lock audibly.
- Guide in the wiring harness section of the transmission wiring harness and install.
- Fasten the cable using the clamp (arrowed).
- Connect the connector (1) to the air conditioning compressor and lock audibly.
- Guide in the wiring harness section of the transmission wiring harness and install.
- Make sure the locking mechanism (1) engages audibly.
- Tighten the screws (2).TIGHTENING TORQUES SPECIFICATION
Cable bracket on rear cylinder head/transmission M6 x 20 tightening torque 8 Nm - Connect connector (3) and lock audibly.
- Connect connector (4) and lock audibly.
- Install all connectors (1) to the DME control unit and the integrated power supply module.
Follow-up work
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING TANK COVER ON LEFT AND RIGHT .
- Refer to INSTALL CONTROL UNIT BRACKET .
- Refer to INSTALL THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to SECURING THE HIGH-VOLTAGE CABLES ON THE EME .
- Refer to INSTALLING THE SECOND END PANEL UNDERNEATH .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
- Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
- Refer to INSTALLING BATTERY COVER IN TRUNK .
- Refer to CONNECTING THE NEGATIVE BATTERY CABLE (12 V BATTERY) .
- Refer to ACTIVATING HIGH-VOLTAGE SYSTEM .
- Refer to INSTALLING FLAP IN RIGHT LUGGAGE COMPARTMENT TRIM PANEL .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .