51 61 Reinforcement, Body (X6 M)
51 61 REINFORCEMENT, BODY - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Suspension cross-brace in engine compartment, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Replace screws | |
| Joining torque | 30 Nm | |||
| Angle of rotation | 90° | |||
| F15/F16 | Replace screws | |||
| Joining torque | 25 Nm | |||
| Angle of rotation | 90° | |||
| F25/F26 | M10x25 | Replace screws | ||
| Joining torque | 56 Nm | |||
| Angle of rotation | 90° | |||
| 2AZ Suspension cross-brace in engine compartment, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x25 | 56 Nm | |
| F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Replace screws | ||
| Joining torque | 30 Nm | |||
| Angle of rotation | 90° | |||
| 3AZ Connection, rear, to carrier support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 28 Nm | ||
| 4AZ Connection, front, to connection, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 5AZ Engine compartment lid catch | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8x20 | 11.8 Nm | |
| 6AZ V-support to connection, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 7AZ Air duct, lower, to vertical strut | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 8AZ Air duct, lower, to carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 9AZ Air duct, upper, on lock support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 10AZ Trailing link/V-strut on side member | F07/F11/F12/F13 | M12 | Replace screws | |
| Joining torque | 100 Nm | |||
| Angle of rotation | 90° | |||
| 11AZ Trailing link to compression strut, rear axle | F07/F11/F12 | M8 | 19 Nm | |
| 12AZ Trailing link to cross reinforcement (rear end support) | F07/F11/F12 | M12 | Replace screws | |
| Joining torque | 100 Nm | |||
| Angle of rotation | 90° | |||
| 13AZ Cross reinforcement (support, rear end) to rear end | F07/F11/F12 | M10x22 | 38 Nm | |
| 14AZ Cross reinforcement (support, rear end) to cross-member | F07/F11/F12 | M10 | 38 Nm | |
| 15AZ Torsion struts/stiffening plate to front axle support | F01/F02/F03/F12 | M10 | Replace screws | |
| Joining torque | 56 Nm | |||
| Angle of rotation | 90° | |||
| 16AZ Rear trailing link | F10/F12 | M10x40 | Replace screws | |
| Joining torque | 56 Nm | |||
| Angle of rotation | 105° | |||
| 17AZ Rear trailing link | F10/F12 | M8x35 | Replace screws | |
| Joining torque | 28 Nm | |||
| Angle of rotation | 90° |