32 21 Steering Arms
WARNING: This page does not describe the selected car, but rather 38 other vehicles, including the 2006 BMW M3, 2006 BMW 330Ci, 2006 BMW 325Ci, 2005 BMW M3, and 2005 BMW 330xi. However, it is still accessible from the selected car via links, so may be relevant.
STEERING ARMS TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Tie rod to ball joint (castle nut) | E21 | 60 Nm | ||
| 2AZ Tie rod/axial joint to rack | E21 / E30 | 75 Nm | ||
| E36 / E34 / E39 / E52 | 71 Nm | |||
| E46 / E85 | 100 + 10 Nm | |||
| E53 / E60, E61 (AWD) / E83 | 110 + 10 Nm | |||
| E60, E61 (except AWD) / E63 / E64 / E65 / E66 / E67 | 110 Nm | |||
| 3AZ Tie rod end to steering knuckle / swivel bearing Attention! Tie rod end with split-pin hole must not be bolted with a self-locking nut! | E34 (325ix) | 50 Nm | ||
| E38 / E39 / E46 / E52 / E85 | Replace nut | 65 Nm | ||
| E53 / E60, E61 (AWD) / E67 / E83 | Replace nut | 80 Nm | ||
| E60, E61 (except AWD) / E63 / E64 / E65 / E66 | Replace nut | 165 Nm | ||
| other | 36.5 +/- 3.5 Nm | |||
| 4AZ Tie rod clamping screw | E38, E39 | tighten in normal position | 27 Nm | |
| all others | tighten in normal position | 14 Nm | ||
| 5AZ Tie rod end to tie rod (clamping nut) | E36, E46, E34 / 325iX, E85 | 45 Nm | ||
| E39 / E52 / E53 / E60 / E61 / E63 / E64 / E65 / E66 / E67 / E83 | 51 Nm | |||
| 6AZ Steering drop arm to steering gear | E32, E34 | 59 Nm | ||
| M26 | Tightening value may be exceeded up to correct position to locking plate | at least 180 Nm | ||
| M22 | Tightening value may be exceeded up to correct position to locking plate | at least 140 Nm | ||
| E38 / E39 | Note direction of screw thread. In direction of travel: from left on LHD or from right on RHD vehicle | 61 Nm | ||
| E31 | 70 Nm | |||
| 7AZ Steering guide arm to front axle carrier | E39 | 62 Nm | ||
| All | M10 | 42 Nm | ||
| All | M12 | 85 Nm | ||
| 8AZ Track rod arm to strut | E12, E24 / until 5.82 | Bolts secured with: Wire | 55 Nm | |
| E28, E23, | Bolts secured | 62 Nm | ||
| E24 / from 5.82 | with: Loctite No. 270 Clean threads of tapped bores and bolts. | |||
| E31, E32, E34 | Bolts secured with: Loctite No. 270 Clean threads of tapped bores and bolts. | 110 Nm | ||
| M3 | Bolts secured with: Loctite No. 270 Clean threads of tapped bores and bolts. | 30 Nm | ||
| 9AZ Tie rod arm to control arm | E12, E23, E24 / until 5.82 | 66 Nm | ||
| M3 | 66 Nm | |||
| E24 / from 5.82, E28, E32, E31, E34 | 93 Nm | |||
| 10AZ Leading strut to tie rod arm | E23 | 93 Nm | ||
| 11AZ Trailing strut to tie rod arm | E31, E32, E34 | 93 Nm |