26 11 Propeller Shaft complete
WARNING: This page is about a different car, the 2018 BMW 330i xDrive and 2017 BMW 330i xDrive. However, it is still accessible from the selected car via links, so may be relevant.
26 11 PROPELLER SHAFT COMPLETE - TIGHTENING TORQUES SPECIFICATIONS
| Type | Thread | Instructions | Torque Specification | |
|---|---|---|---|---|
| 1AZ Front flexible disc to transmission output flange ZNS screws and nuts All versions |
F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV |
M12-10.9 |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw Jointing torque Angle of rotation |
55 Nm 90° |
| 2AZ Front flexible disk to propeller shaft ZNS screws and nuts All versions |
F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV |
M12-10.9 |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut Jointing torque Angle of rotation |
55 Nm 90° |
| 3AZ Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions |
F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F36/F85/F86/F18 PHEV |
ASA M12-10.9 |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw Jointing torque Angle of rotation |
55 Nm 90° |
| 4AZ Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions |
F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV |
M12-10.9 |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut Jointing torque Angle of rotation |
55 Nm 90° |
| 5AZ Center mount to body | F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | 19 Nm | ||
| 6AZ Input flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86 PHEV/F15 PHEV/F87/F30 PHEV | Replace insert nut! Allow min. 2 hours hardening time | 100 Nm | |
| 7AZ Front propeller shaft to transfer box/front axle differential | F01/F02/F06/F07/F10/F11/F12/F13/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F36/F85/F86/F15 PHEV | Replace screws, jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
20 Nm 45° |
|
| 8AZ Constant velocity joint propeller shaft to rear axle differential | F06 M6/F10 M5/F12 M6/F13 M6 | M10 | Replace screws and shims, jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
20 Nm 90° |
| 9AZ Front propeller shaft to rear propeller shaft/constant velocity joint | F06 M6/F10 M5/F12 M6/F13 M6 | M12x1 | 60 Nm |