11 31 574 Adjusting camshaft timing on right side (N63)

Special tools required:

IMPORTANT: Release central bolts on adjuster only with special tool 2 249 117 .
Risk of damage to timing drive.

(cylinder bank 1 to 4)

Necessary preliminary tasks:

Remove RIGHT-HAND GEAR CASE COVER .
Check CAMSHAFT TIMING ON RIGHT SIDE .

Get set of special tools 2 249 117 ready for securing camshafts.

Fig 1: Identifying Set Of Special Tools (2 249 117)

Courtesy of BMW OF NORTH AMERICA, INC.

Position special tool 2 249 137 on intake camshaft.

Position exhaust camshaft with special tool 2 249 140 and attach to special tool 2 249 137 .

Fig 2: Identifying Special Tools (2 249 137 And 2 249 140) On Camshafts

Courtesy of BMW OF NORTH AMERICA, INC.

Release central bolts (1 and 2) of intake and exhaust camshaft adjusters.

Installation note:

Replace central bolts after releasing.

Fig 3: Identifying Central Bolts Of Intake And Exhaust Camshaft Adjusters

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Check whether head of central bolt (1) is greased (see arrow).

Installation note:

Coat contact surface of new central bolt (1) with copper paste.

Fig 4: Identifying Central Bolt

Courtesy of BMW OF NORTH AMERICA, INC.

Insert central bolts (1 and 2).

IMPORTANT: Loosen the central bolts (1 and 2) by maximum 40°.

Fig 5: Identifying Central Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

Remove special tool 11 9 190 .

Fig 6: Turning Engine Central Bolt And Positioning Special Tool (11 9 190) In Gear Case Cover

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Crank engine back at central bolt through 8°.

Position engine with special tool 11 9 190 in front of special tool 11 8 570 as shown in illustration.

Fig 7: Identifying Special Tools

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note:

The tightening sequence begins with the exhaust camshaft.

Insert central bolt (1) of exhaust camshaft with special tool 11 4 350 .

Joining torque 5 Nm .

Fig 8: Inserting Exhaust Camshaft Central Bolt With Special Tool (11 4 350)

Courtesy of BMW OF NORTH AMERICA, INC.

Insert central bolt (1) of intake camshaft with special tool 11 4 350 .

Joining torque 5 Nm .

Fig 9: Inserting Intake Camshaft Central Bolt With Special Tool (11 4 350)

Courtesy of BMW OF NORTH AMERICA, INC.

Remove special tool 11 9 190 .

Fig 10: Identifying Special Tools

Courtesy of BMW OF NORTH AMERICA, INC.

Turn the engine at the central bolt further until the special tool 11 9 190 can be positioned in the gear case cover.

The engine is now in the 150° crankshaft position before the TDC firing position of cylinder 1.

Fig 11: Turning Engine Central Bolt And Positioning Special Tool (11 9 190) In Gear Case Cover

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note:

Tighten central bolts beginning with the exhaust camshaft.

Insert central bolt (1) of exhaust camshaft with torque.

Tightening torque of 30 Nm

Fig 12: Tightening Central Bolt Of Exhaust Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Insert central bolt (1) of intake camshaft with torque.

Tightening torque of 30 Nm

Fig 13: Tightening Central Bolt Of Intake Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Insert central bolt (1) of exhaust camshaft with special tool 00 9 120 .

Torsion angle adjustment 90 °. Refer to 11 36 1AZ .

Fig 14: Tightening Exhaust Camshaft Central Bolt With Special Tool (00 9 120)

Courtesy of BMW OF NORTH AMERICA, INC.

Insert central bolt (1) of intake camshaft with special tool 00 9 120 .

Torsion angle adjustment 90 °. Refer to 11 36 1AZ .

Remove special tool 2 249 117 .

Fig 15: Tightening Intake Camshaft Central Bolt With Special Tool (00 9 120)

Courtesy of BMW OF NORTH AMERICA, INC.

Remove special tools 11 9 190 and 11 8 570 .

Crank engine at central bolt twice in direction of engine rotation until engine returns to 150° before cylinder no. 1 firing TDC position .

Secure vibration damper with special tools 11 8 570 and 11 9 190 in the 150° TDC firing position, cylinder 1 .

Fig 16: Turning Engine Central Bolt And Positioning Special Tool (11 9 190) In Gear Case Cover

Courtesy of BMW OF NORTH AMERICA, INC.

Fit special tool 2 249 137 on intake camshaft and check timing adjustment.

NOTE: Timing is correctly adjusted when special tool 2 249 137 rests without a gap on cylinder head.

Fig 17: Fitting Special Tool (2 249 137) On Intake Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Place special tool 2 249 140 on the exhaust camshaft and check timing adjustment.

NOTE: Timing is correctly adjusted when special tool 2 249 140 rests without a gap on special tool 2 249 137 .

Fig 18: Identifying Special Tools (2 249 137 And 2 249 140) On Camshafts

Courtesy of BMW OF NORTH AMERICA, INC.

Remove all special tools.

Assemble engine.