37 14 Electric components
WARNING: This page is about a different car, the 2013 BMW X5, 2012 BMW X5, and 2011 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - ELECTRIC COMPONENTS
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Bracket, ride height sensor, to body | E70, E70M/E71, E71M/E72 | M6 | 8 Nm | |
| 2AZ | Ride height sensor holder to rear axle support | E70, E70M/E71, E71M/E72 | M6 | 8 Nm | |
| 3AZ | Ride height sensor to holder | E70, E70M/E71, E71M/E72 | M5 | 5 Nm | |
| 4AZ | Sensor lever, ride height sensor to jointed rod | E70, E70M/E71, E71M/E72 | M6 | Replace nut | 8 Nm |
| 5AZ | Jointed rod to upper wishbone | E70, E70M/E71, E71M/E72 | M6 | Replace nut | 8 Nm |
| 6AZ | Jointed rod to swinging arm | E70, E70M/E71, E71M/E72, | M6 | Replace nut | 8 Nm |
| 7AZ | Acceleration sensor to body | E70, E70M/E71, E71M | M6 | 8 Nm | |
| 8AZ | Control unit Dynamic Drive ECU to cockpit support structure | E70, E71 | M5x15 | 6 Nm | |
| 9AZ | Valve block to holder | E70, E70M/E71, E71M/E72 | M6 | 8 Nm | |
| 10AZ | Holder, valve block, to body | E70, E70M/E71, E71M/E72 | M6 | Replace nuts | 8 Nm |
| 11AZ | Dynamic Drive pressure line to valve block | E70, E71 | 50 Nm | ||
| 12AZ | Return line to valve block | E70, E71 | 40 Nm | ||
| 13AZ | Control lines for oscillating motor, front, to valve block | E70, E71 | M14 | 35 Nm | |
| 14AZ | Control lines for oscillating motor, rear, to valve block | E70, E71 | M14 | 35 Nm | |
| 15AZ | Connecting nuts, hydraulic lines (pressure line/control lines) | E70, E71 | 30 Nm | ||
| 16AZ | Connecting nuts, hydraulic lines (return) | E70 | 35 Nm | ||
| 17AZ | Line holder/pipe holder/holder | E70/E71/E72 | M6 | 8 Nm | |
| E70/E71/E72 | M8 | 20.5 Nm | |||
| 18AZ | Control lines to oscillating motor | E70, E70M/E71, E71M | 30 Nm | ||
| 19AZ | Heat shield to rear axle carrier | E70, E70M/E71, E71M/E72 | M10 | 38 Nm | |
| E70, E70M/E71, E71M/E72, | M6 | 8 Nm | |||
| 20AZ | Retaining bar, stabilizer, to front axle carrier | E70, E70M/E71, E71M/E72 | M10 | 56 Nm | |
| 21AZ | Retaining bracket, anti-roll bar to rear axle support | E70, E70M/E71, E71M/E72 | M10 | 56 Nm | |
| 22AZ | Screw pins for pipe holder | E70, E70M/E71, E71M/E72 | Replace screw pins | 1.5 Nm | |
| 23AZ | Spring-type actuator to oscillating motor, front | E70 | 30 Nm | ||
| 24AZ | Pressure relief valve to oscillating motor, front | E70 | 14 Nm | ||
| 25AZ | Line holder for control lines to front axle oscillating motor | E70/E71 | 3 Nm | ||
| 26AZ | Lines to spring-type actuator | E70 | 14 Nm | ||
| 27AZ | Block screw connection, hydraulic lines | E70, E70M/E71, E71M | 12 Nm | ||