24 00 Transmission in general
WARNING: This page is about a different car, the 2013 BMW X5, 2012 BMW X5, and 2011 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - TRANSMISSION IN GENERAL
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Transmission to engine | ||||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | 24 Nm | ||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M10 | 45 Nm | ||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M12 | 82 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M8 | 21 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M10 | 42 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M12 | 72 Nm | ||
| Torx bolts | GA6HP19Z/GA6HP26Z | M6 | 9 Nm | ||
| Torx bolts | GA6HP26Z | M10 | 38 Nm | ||
| Steel Torx screws | GA6HP19Z/GA6L26Z/GA6L45R | M8 | 19 Nm | ||
| Steel Torx screws | GA6HP19Z/GA6HP26Z/GA6L45R | M12 | 66 Nm | ||
| 2AZ | Transmission to engine N51/N52/N52K/N53/N54/N55 Aluminum screws are not magnetic | GA6HP19Z/GA6HP26Z/GA6L45R | Replace screws Jointing torque and angle of rotation must be observed without fail | ||
| GA6HP19Z/GA6L45R | M10x30 | Jointing torque | 20 Nm | ||
| Angle of rotation | 90-110 ° | ||||
| GA6HP19Z | M10x85 | Jointing torque | 20 Nm | ||
| Angle of rotation | 180-200 ° | ||||
| GA6HP19Z/GA6L45R | M12 | Jointing torque | 25 Nm | ||
| Angle of rotation | 130 ° | ||||
| 3AZ | Reinforcement shell to transmission/extension | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | 23 Nm | |
| 4AZ | Cover plate for transmission | GA6HP19Z/GA6L45R | M6 | 9 Nm | |
| 5AZ | Heat shield, oil sump | GA6L45R/GA6HP19Z | M6 | 8 Nm | |
| 6AZ | Air duct plate | GA6HP26Z | M6 | 10 Nm | |
| 7AZ | Line cover plate | GA6HP26Z | M6 | 10 Nm | |