63 10... Test requirements for headlights vertical aim adjustment
Attention!
Do not perform headlight adjustment immediately after lowering the vehicle on the vehicle hoist. In this case, shift the vehicle for approx. 15 m on its own wheels before headlight adjustment.
Attention!
Observe the operating instructions for the headlight adjusting device!
The headlight setting space must comply with the specifications as set out in German road traffic licensing regulations (German road traffic licensing regulations) 29 Annex 8d (or ISO 10604)!
- Park vehicle on flat and even surface.
- Replace faulty glass and mirrors and blackened light bulbs.
- Check correct adjustment of headlights in relation to engine compartment lid (gap dimensions).
- Check tire pressure and correct if necessary.
Only halogen headlight, front fog light and headlight for Dynamic Marker Light (Dynamic Light Spot). Not required in vehicles with automatic headlight beam throw adjustment:
- Apply load equivalent to one person on driver's seat (approx. 75 kg).
- Vehicle with full fuel tank or appropriate additional weight in trunk.
- Switch on ignition.
- Manual headlight beam throw adjustment: Shift handwheel to neutral position (1).
- Light switch must be in "lowbeam headlight/low beam" position (3).
- Do not carry out the headlight adjustment in the "automatic headlight control" light switch position (2).
- Version with Xenon or LED (automatic headlight beam throw adjustment) : Wait 80 s after switching on lights. During this time, do not move the vehicle and avoid vibrations.
Attention!
Do not move the vehicle and steering wheel during the measuring and adjustment procedures!
Wheels must be in the straight-ahead position!
Attention!
A correct measurement/adjustment requires exact positioning of the headlight adjusting device (1)!
The headlight adjusting device (1) must stand vertically to the vehicle longitudinal axis!
This applies to all headlights!
Position the headlight adjusting device (1) centrally in front of the vehicle (2) at distance (A) = 10 cm .
Align headlight adjusting device (1) according to laser beam (3). Laser beam (3) must hit two suitable points, for example marked by arrows.
Attention!
Points must be vehicle proof!
Points must be separated as wide as possible!
Trim panels are not suitable!
If the headlight adjusting device (1) does not have a laser beam (3), complete the alignment analogous with the line in the mirror.
Attention!
Always perform positioning of the headlight adjusting device (1) at the outer headlight (2)!
The center of the collecting lens (1) must match the center of headlight (2) horizontally.
Corrections are made by raising or lowering the headlight adjusting device.
When positioned correctly, the light/dark boundary of the headlight (marked with arrow) must hit the collecting lens of the adjustment device in the center:
- The headlight adjusting device is too low.
- The headlight adjusting device is positioned correctly.
- The headlight adjusting device is too high.
The center of the collecting lens (1) must match the center of headlight (2) vertically.
Corrections are made by sliding the side of the headlight adjusting device to the left or right.
Refer to OVERVIEW OF TRANSPARENT SCREENS OF DIFFERENT HEADLIGHT TYPES .
Set the marker line {M} on the headlight adjusting device to dimension {e}. Scale graduations on the headlight adjusting device show a gradient in cm at a distance of 10 meters.
Light/dark boundary of headlights in headlight adjusting device
{e} Setting dimension, headlights:
- Value is indicated on the headlight housing
and on vehicles with production date up to 2011 on the nameplate
in %.
(e.g.: 1.0 % = -10 cm/10 m = - 1.0 % on the headlight adjusting device)
- Value 1.0 % (adjustment value - 1.0 % ) applies to all BMW Group vehicles.
- Exception: E53, E70, E71, E72, E83, F15, F16, F25, F26, R60, R61, F60. For these vehicles, value 1.1 % (adjustment value - 1.1 % ) applies.
Setting dimension, fog lights:
- Value 2.0% = -20 cm/10 m = - 2.0% on the headlight adjustment device applies to all BMW Group vehicles.
Headlight setting dimension, dynamic marker light (dynamic spotlight):
- Value 0.0% = 0 cm/10 m = 0% on the headlight adjustment device applies to all BMW Group vehicles.
{H} Height of headlight center above standing surface
{h} {H} - {e} = height of marking line above standing surface
+ Central mark = center point of high beam headlight.
{M} Marker line of the headlight adjusting device
{S} Standing surface of the vehicle and headlight adjusting device
Setting dimension {e} is only valid for EUR. Observe differing national regulations.