5161 Reinforcement, Body
51 61 REINFORCEMENT, BODY - TIGHTENING TORQUE SPECIFICATION
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1 AZ Suspension cross brace to body | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F87 | M10 | Renew screws. Tightening torque Angle of rotation |
56 Nm 90° |
| 2AZ Rear trailing link | F31/F34/F36 | M10 | Renew screw. | 56 Nm |
| M12 | Renew screw. Tightening torque Angle of rotation |
100 Nm 90° |
||
| 3AZ Strut, front partition wall | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F87 | 19 Nm | ||
| 4AZ Front end strut to body | F23/F33/F87 | 28 Nm | ||
| 5AZ Diagonal strut to adapter plate | F33 | Tightening torque Angle of rotation |
56 Nm 90° |
|
| 6AZ Torsion strut to front axle support | F23/F33 | M10 | Replace screws Tightening torque Angle of rotation |
56 Nm 45° |
| 7AZ Torsion strut to side member | F23/F33 | M12 | Replace screws Tightening torque Angle of rotation |
100 Nm 90° |
| 8AZ Rear tension strut to cross member of luggage compartment floor | F33/F23 | Renew screw | 56 Nm | |
| 9AZ Rear tension strut to support | F33/F23 | Renew screw. Tightening torque Angle of rotation |
100 Nm 90° |
|
| 10AZ Rear tension strut to side member | F33/F23 | Renew screw Tightening torque Angle of rotation |
100 Nm 90° |
|
| 11 AZ Carbon brace on lock support | F80/F82/83 | Renew screw. | 28 Nm | |
| 12AZ Carbon brace on strut brace | F80/F82/F83 | Renew screw. | 28 Nm | |
| 13AZ Cross-brace to spring strut dome | F80/F82/F83 | M8 | 28 Nm | |
| 14AZ Cross-brace to side panel | F80/F82/F83 | M10 | 34 Nm | |
| 15AZ Cross-brace to bulkhead | F80/F82/F83 | M10x25 | Renew screw. Tightening torque Angle of rotation |
56 Nm 90° |
| 16AZ Cross-brace extension/additional strut to cross-brace | F80/F82/F83 | M8 | 28 Nm | |
| 17AZ Cross-brace extension to body | F80/F82/F83 | M10 | 56 Nm | |
| 18AZ Additional strut to cross-brace extension | F80/F82/F83 | M8 | 28 Nm | |
| 19AZ Torsion strut to front adapter plate | F23/F33 | M10 | Renew screw. Tightening torque Angle of rotation |
56 Nm 90° |
| 20AZ Torsion strut to body | F23/F33 | M8 | 19 Nm | |
| 21AZ Engine bulkhead, bottom to body | F20/F21 | M8x18 | 19 Nm | |
| 22AZ Rollover protection bar to body | F82 GTS | M8x16 | 19 Nm | |
| 23AZ Rollover protection bar to body | F82 GTS | M10x30 | 38 Nm |