11 61 050 Removing and installing/replacing intake plenum (230i and 230i xDrive coupe/convertible)

Necessary preliminary work: 

• Refer to REMOVING ACOUSTIC COVER AT FRONT .
• Refer to REMOVING ACOUSTIC COVER AT REAR .
• Refer to DRAINING LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to REMOVING TANK VENT VALVE .
• Refer to REMOVING ELECTRONICS BOX .

Removal: 

Unlock coolant return line (1) with screwdriver (2) and remove.

Courtesy of BMW OF NORTH AMERICA, INC.

Release the coolant return line at clamp (1) from the intake plenum.

Loosen screws (2) and lay engine wiring harness to one side.

Unlock coolant line (3) and detach from intake plenum.

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock connector (1) and pull off.

Unclip engine wiring harness in the marked area.

Unlock holder (2) and place the injector wiring harness (3) to one side.

Disconnect ventilation line (4) in the marked area from the intake plenum.

Courtesy of BMW OF NORTH AMERICA, INC.

Disconnect ventilation line (1) in the marked area.

Unlock ventilation line (2) and remove from intake plenum.

Release screw (3) and feed out ventilation line (4).

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock and pull off connectors (1 and 2).

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock coolant feed line (1) and pull off.

Unlock clamp (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1).

Disconnect coolant feed line (2).

Lay holder (3) to one side.

Courtesy of BMW OF NORTH AMERICA, INC.

Attention! 

Additional coolant can escape.

See that no coolant enters the intake ports.

Release bolts in sequence (5 to 1).

Feed out intake plenum.

Replacement: 

Remounting throttle body (1).

Remounting the charging pressure sensor.

Courtesy of BMW OF NORTH AMERICA, INC.

Installation: 

Courtesy of BMW OF NORTH AMERICA, INC.

Position the intake plenum.

Tighten screws in the sequence (1 - 5).

Tightening torque: 11 61 1AZ .

Position holder (3).

Connect coolant feed line (2) to the clamp.

Tighten down screws (1).

Tightening torque 11 61 2AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (1).

Tightening torque 11 61 4AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Lock clamp (2).

Connect coolant feed pipe (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Route the wiring harness correctly and connect connectors (1 and 2).

Courtesy of BMW OF NORTH AMERICA, INC.

Position ventilation line (4).

Tighten screw (3).

Tightening torque 11 61 6AZ .

Connect ventilation line (2).

Clip in ventilation line (1) in the marked area.

Courtesy of BMW OF NORTH AMERICA, INC.

Connect ventilation line (4) in the marked area.

Position injector wiring harness (3) and clip in holder (2).

Clip in engine wiring harness in the marked area.

Connect the connector (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Connect and lock coolant line (3).

Route the engine wiring harness correctly and fasten with screws (2).

Tightening torque 11 61 5AZ .

Clip in coolant return line at clamp (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Lock coolant return line (1) and connect to intake plenum.

Courtesy of BMW OF NORTH AMERICA, INC.

Required reworking: 

• Refer to INSTALLING THE TANK VENT VALVE .
• Refer to INSTALLING THE ELECTRONICS BOX .
• Refer to TOPPING UP LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING THE ACOUSTIC COVER, REAR .
• Refer to INSTALLING THE ACOUSTIC COVER AT FRONT .