11 41 Oil Pumps With Strainer And Drive
N55 ENGINE (2016-2018):
11 41 OIL PUMP WITH STRAINER AND MOTOR - TIGHTENING TORQUE SPECIFICATION
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Intake pipe with oil deflector to crankcase lower section (bedplate) | N55 | M6x30 | Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
4 Nm 90° |
| 2AZ Oil pump to bedplate | N55 | M8x123 | Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
10 Nm 180° |
| N55 | M8x31 M8x37 |
Replace screws Thread repairs exclusively with AI Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
10 Nm 90° |
|
| 3AZ Chain module to crankcase and oil pump | N55 | M6x16 | Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
4 Nm 45° |
| 4AZ Hydraulic valve of oil pump to crankcase | N55 | M6x16 | Jointing torque Angle of rotation |
4 Nm 45° |
| 5AZ Sprocket to oil pump | N55 | M8 | Jointing torque Angle of rotation |
20 Nm 45° |
| 6AZ Triangular drive to oil pump | N55 | M6x16 | Jointing torque Angle of rotation | 4 Nm 45° |
| 7AZ Chain tensioner to crankcase | N55 | M6x16 | 10 Nm |
S55 ENGINE (2019-2022):
11 41 OIL PUMP WITH STRAINER AND MOTOR - TIGHTENING TORQUE SPECIFICATION
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Oil pump to lower section of crankcase (bedplate) | S55 | M8x123 | Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque |
10 Nm |
| Angle of rotation | 180° | |||
| S55 | M8x31 M8x37 |
Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque |
10 Nm | |
| Angle of rotation | 90° | |||
| 2AZ Intake pipe with oil deflector to crankcase lower section (bedplate) | S55 | M6x30 | Replace screws Thread repairs exclusively with Al Helicoil. Jointing torque and angle of rotation must be observed without fail. Jointing torque |
4 Nm |
| Angle of rotation | 100° | |||
| 3AZ Oil suction pump to lower section of crankcase (bedplate) | S55 | M6x40 | 10 Nm | |
| 4AZ Suction pipe, right, to oil deflector suction pipe | S55 | M6x40 | 10 Nm | |
| 5AZ Suction pipe, left, to oil pump | S55 | M6x16 | 10 Nm | |
| 6AZ Reverse exhaust turbocharger suction pipe to oil deflector | S55 | M6x16 | 10 Nm | |
| 7AZ Chain module to crankcase and oil pump | S55 | M6x16 | 10 Nm | |
| 8AZ Hydraulic valve of oil pump to crankcase | S55 | M6x16 | 10 Nm | |
| 9AZ Sprocket to oil pump | S55 | M8 | ||
| Jointing torque | 20 Nm | |||
| Angle of rotation | 45° | |||
| 10AZ Chain tensioner to crankcase | S55 | M6x28 | 10 Nm | |