Installing the thermostat on the transmission oil lines
Preparing the thermostat for installation
- Check the gaskets (1) .
- Replace damaged seals (1)
.
Parts: Seals
- Check the gaskets (1) .
- Replace damaged seals (1)
.
Parts: Seals
- Insert and install the thermostat (2) in the guides (3) .
- Ensure that the locking mechanism (1)
engages audibly.
- Feed in and install transmission oil lines (2) .
- Tighten down screw (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Transmission oil lines to thermostat/automatic transmission | ||
|---|---|---|
| M6X25 | Tightening torque | 8 Nm |
- Feed in and install transmission oil lines (2) .
- Tighten down screw (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Transmission oil lines to thermostat/automatic transmission | ||
|---|---|---|
| M6X25 | Tightening torque | 8 Nm |
- Feed in and install transmission oil lines (2) .
- Tighten down screw (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Transmission oil lines to thermostat/automatic transmission | ||
|---|---|---|
| M6X25 | Tightening torque | 8 Nm |
- Version A:
Insert and install the holder (2) .
Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Holder of high-voltage cable to automatic transmission | ||
|---|---|---|
| M6X12 | Tightening torque | 8 Nm |
- Version A:
Position the high-voltage cable (1) on the holder (3) in the direction of the arrow.
Insert and install the holder (2) .
- Version A:
Position holder (2) .
Tighten down screw (1) .
TIGHTENING TORQUE SPECIFICATIONS
| High-voltage cable to holder | ||
|---|---|---|
| M6x12/M6x14 | Tightening torque | 8 Nm |
- Version B:
Fasten the high-voltage cable (2) to the holder.
Tighten nut (1) .
TIGHTENING TORQUE SPECIFICATIONS
| High-voltage cable to holder | ||
|---|---|---|
| M6x12/M6x14 | Tightening torque | 8 Nm |
- Version B:
Position holder (2) .
Tighten down screw (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Holder of high-voltage cable to automatic transmission | ||
|---|---|---|
| M6X12 | Tightening torque | 8 Nm |
- Guide in and install the high-voltage connector (2) .
- Tighten the screws (1) crosswise up to the high-voltage connector (2) .
- Tighten screws (1) crosswise.
TIGHTENING TORQUE SPECIFICATIONS
| High-voltage cable to automatic transmission | ||
|---|---|---|
| M6X25 | Tighten screws in crosswise sequence. Joining torque |
3 Nm |
| Tightening torque | 8 Nm | |
- Feed in and install the heat shield (2) .
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Heat shield on convenience charging electronics (KLE) | ||
|---|---|---|
| Tightening torque | 3 Nm | |
Follow-up work
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
- Refer to INSTALLING THE REAR THRUST FIELD .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
- Refer to INSTALLING REAR UNDERBODY PROTECTION .
- Refer to INSTALLING THE UNDERBODY PLANKING OF THE TRANSMISSION ON THE SIDE .