33 32 Axle guide and axle strut
WARNING: This page is about a different car, the 2018 BMW 330i and 2017 BMW 330i. However, it is still accessible from the selected car via links, so may be relevant.
33 32 AXLE GUIDE AND AXLE STRUT - TIGHTENING TORQUE SPECIFICATION
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Trailing arm to rear axle support | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace nut. Tighten in normal position. |
100 Nm |
| 2AZ Trailing arm to wheel carrier | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace nut. Tighten in normal position. |
100 Nm |
| 3AZ Control arm to rear axle support | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace nut. Tighten in normal position. |
100 Nm |
| 4AZ Control arm to wheel carrier | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace screw. Tighten in normal position. |
|
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90° | |||
| 5AZ Wishbone to rear axle support | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace nut. Tighten in normal position. |
100 Nm |
| 6AZ Wishbone to wheel carrier | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace screw. Tighten in normal position. |
|
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90° | |||
| 7AZ Toe arm to rear axle support | F20/F21/F22/F23/F30/F31/F32/F33/F35 | M12 | Replace nut. Tighten in normal position. |
100 Nm |
| F34/F36 | M12 | Replace nut. Tighten in normal position. |
108 Nm | |
| 8AZ Toe arm to wheel carrier | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M12 | Replace screw. Tighten in normal position. |
|
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90° | |||
| 9AZ Camber control arm to rear axle support | F20/F21/F22/F23/F30/F31/F32/F33/F35 | M14 | Replace nut and screw. Tighten in normal position. |
165 Nm |
| F34/F36 | M14 | Replace nut. Tighten in normal position. |
175 Nm | |
| 10AZ Camber control arm to wheel carrier | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M14 | Replace nut. | 165 Nm |
| 11AZ Aerodynamic cover on camber arm | F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36 | M6 | Replace nuts. | 4 Nm |
| 12AZ Tension strut to body | F20/F21/F22/F23/F31/F32/F33/F34/F36 | M8 | 24 Nm | |
| 13AZ Tension strut to compression strut | F20/F21/F22/F23/F31/F32/F33/F34/F36 | M12 | Replace screws. | |
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90° |