26 11 Propeller Shaft, complete
2611 PROPELLER SHAFT (COMPLETE) - TIGHTENING TORQUES SPECIFICATION
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Front flexible disc to transmission output flange ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90° |
|
| 2AZ Front flexible disk to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90° |
|
| 3AZ Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F36/F85/F86/F18 PHEV | ASA M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90° |
|
| 4AZ Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV | M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90° |
|
| 5AZ Center mount to body | F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | 19 Nm | ||
| 6AZ Input flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86 PHEV/F15 PHEV/F87/F30 PHEV | Replace insert nut! Allow min. 2 hours hardening time | 100 Nm | |
| 7AZ Front propeller shaft to transfer box/front axle differential | F01/F02/F06/F07/F10/F11/F12/F13/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F36/F85/F86/F15 PHEV | Replace screws, jointing torque and angle of rotation must be observed without fail. | ||
| Jointing torque | 20 Nm | |||
| Angle of rotation | 45° | |||
| 8AZ Constant velocity joint propeller shaft to rear axle differential | F06 M6/F10 M5/F12 M6/F13 M6 | M10 | Replace screws and shims, jointing torque and angle of rotation must be observed without fail. | |
| Jointing torque | 20 Nm | |||
| Angle of rotation | 90° | |||
| 9AZ Front propeller shaft to rear propeller shaft/constant velocity joint | F06 M6/F10 M5/F12 M6/F13 M6 | M12x1 | 60 Nm |