22 11 Engine mounting
WARNING: This page is about a different car, the 2013 BMW Z4, 2012 BMW Z4, 2011 BMW Z4, 2010 BMW Z4, and 2009 BMW Z4. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - ENGINE MOUNTING
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Engine mount to front axle support | E52/E85/E86 | 42 Nm | ||
| E65/E66/E67 | M8-8 | 19 Nm | ||
| E60/E61/E63/E64/E83 | M8-8 | 21 Nm | ||
| E53 | M8 - 10.9 | 30 Nm | ||
| E87/E90/E91/E92/E93/E70/E71/E83/E81/E82/E88/E89/E84 | M8 10.9 | 28 Nm | ||
| E70/E71/E72/E83/E84/E90/E91/E92/E93 | M10 | 38 Nm | ||
| E92/E90/S65 | M10 | 56 Nm | ||
| 2AZ Engine mount to engine support arm | E60/E61/E63/E64/E65/E66/E67/E53/E83/E87/E90/E91/E92/E93/E70/E71/E81/E82/E88/E89/E84 | M10 10.9 | 56 Nm | |
| E65/E66/E67 | M12 10.9 | 100 Nm | ||
| E70/E71/E72/E83/E84/E90/E91/E92/E93 | M12 | 68 Nm | ||
| E85/E86/E52 | 42 Nm | |||
| 3AZ Engine support arm to engine | E60/E61/E63/E64/E65/E66/E67/E70/E71/E72/E81/E82/E83/E84/E87/E88/E89/E90/E91/E92/E93 | M10 8.8 | 38 Nm | |
| N51/N52/N52K/N53 | M12 | Aluminium bolts must be replaced | ||
| 1. Jointing torque | 25 Nm | |||
| 2. Angle of rotation | 105 ° | |||
| E60/E61/E65/E66/E67 | M8 8.8 | 19 Nm | ||
| E85/E83 | M8 8.8 | 21 Nm | ||
| E70/E71 | M10 10.9 | 56 Nm | ||
| E53 (N62/M54) | 38 Nm | |||
| E53 (M57) | 65 Nm | |||
| N54/N55 | M12 | Engine N54/55 only | 66 Nm | |
| N42 | M10 8.8 | 38 Nm | ||
| 4AZ Engine mount to console | E65/E60/E61/E63/E64 | M8 8.8 | 21 Nm | |
| 5AZ Console to front axle support | E65/E60/E61/E63/E64 | M8-8 | 21 Nm | |
| 6AZ Vibration absorber to engine support | E70/E71 | 19 Nm | ||
| 7AZ Reinforcement plate to front axle support | E90/E91/E92 | M8 | 19 Nm | |
| 8AZ Support angle to engine mount or front axle support | E90/E91/E92 | M8 | 19 Nm |