26 11 Propeller Shaft. complete
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2019 BMW M6 Gran Coupe, 2019 BMW 650i Gran Coupe xDrive, 2019 BMW 650i Gran Coupe, 2019 BMW 640i Gran Coupe xDrive, and 2019 BMW 640i Gran Coupe. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT (COMPLETE)
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Front flexible disc to transmission output flange ZNS screws and nuts All versions | Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90 ° |
|
| 2AZ Front flexible disk to propeller shaft ZNS screws and nuts All versions | Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90 ° |
|
| 3AZ Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions | Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F36/F85/F86/F18 PHEV | ASA M12-10.9 | Jointing torque Angle of rotation |
55 Nm 90 ° |
|
| 4AZ Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions | Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV | M12-10.9 | Jointing torque Angle of rotation 90 ° |
55 Nm | |
| 5AZ Center mount to body | F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV/F15 PHEV/F87/F30 PHEV | 19 Nm | ||
| 6AZ Input flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01/F02/F03/F06/F07/F10/F11/F12/F13/F18 | Replace insert nut! Allow min. 2 hours hardening time Jointing torque Loosen the insert nut through 90° Tightening torque |
120 Nm 85 Nm |
|
| F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86 PHEV/F15 PHEV/F87/F30 PHEV | 85 Nm | |||
| 7AZ Front propeller shaft to transfer box/front axle differential | F01/F02/F06/F07/F10/F11/F12/F13/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F36/F85/F86/F15 PHEV | Renew screws, jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
20 Nm 45 ° |
|
| 8AZ Constant velocity joint propeller shaft to rear axle differential | F06 M6/F10 M5/F12 M6/F13 M6 | M10 | Replace screws and shims, jointing torque and angle of rotation must be observed without fail. Jointing torque Angle of rotation |
20 Nm 90 ° |
| 9AZ Front propeller shaft to rear propeller shaft/constant velocity joint | F06 M6/F10 M5/F12 M6/F13 M6 | M12x1 | 60 Nm |