51 61 Reinforcement, body
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2019 BMW M6 Gran Coupe, 2019 BMW 650i Gran Coupe xDrive, 2019 BMW 650i Gran Coupe, 2019 BMW 640i Gran Coupe xDrive, and 2019 BMW 640i Gran Coupe. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - REINFORCEMENT AND BODY
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Suspension cross-brace in engine compartment, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws Jointing torque Angle of rotation |
30 Nm 90 ° |
| F15/F16 | Renew screws Jointing torque Angle of rotation |
25 Nm 90 ° |
||
| F25/F26 | M10x25 | Renew screws Jointing torque Angle of rotation |
56 Nm 90 ° |
|
| 2AZ Suspension cross-brace in engine compartment, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x25 | 56 Nm | |
| F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws Jointing torque Angle of rotation |
30 Nm 90 ° |
|
| 3AZ Connection, rear, to carrier support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 28 Nm | ||
| 4AZ Connection, front, to connection, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 5AZ Engine compartment lid catch | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8x20 | 11.8 Nm | |
| 6AZ V-support to connection, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 7AZ Air duct, lower, to vertical strut | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 8AZ Air duct, lower, to carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 9AZ Air duct, upper, on lock support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 10AZ Trailing link/V-strut on side member | F07/F11/F12/F13 | M12 | Renew screws Jointing torque Angle of rotation |
100 Nm 90 ° |
| 11AZ Trailing link to compression strut, rear axle | F07/F11/F12 | M8 | 19 Nm | |
| 12AZ Trailing link to cross reinforcement (rear end support) | F07/F11/F12 | M12 | Renew screws Jointing torque Angle of rotation |
100 Nm 90 ° |
| 13AZ Cross reinforcement (support, rear end) to rear end | F07/F11/F12 | M10x22 | 38 Nm | |
| 14AZ Cross reinforcement (support, rear end) to cross-member | F07/F11/F12 | M10 | 38 Nm | |
| 15AZ Torsion struts/stiffening plate to front axle support | F01/F02/F03/F12 | M10 | Renew screws Jointing torque Angle of rotation |
56 Nm 90 ° |
| 16AZ Rear trailing link | F10/F12 | M10x40 | Renew screws Jointing torque Angle of rotation |
56 Nm 105 ° |
| 17AZ Rear trailing link | F10/F12 | M8x35 | Renew screws Jointing torque Angle of rotation |
28 Nm 90 ° |