33 32 Trailing arms and struts
WARNING: This page is about a different variant/trim than selected.
TIGHTENING TORQUE SPECIFICATIONS - TRAILING ARMS AND STRUTS
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Swinging arm/cross-strut to rear axle support, front | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace screw and nut. | 100 Nm | ||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 2AZ | Swinging arm to rear axle support, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace eccentric bolt, eccentric washer and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 3AZ | Swinging arm to wheel carrier, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M16 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
265 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 360 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 4AZ | Swinging arm/integral link | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. | |
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 45 ° | ||||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 5AZ | Integral link to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | 108 Nm | |
| F03 | M16 | 250 Nm | |||
| 6AZ | Toe arm to bearing support/to Integral Active Steering | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace nut. | 100 Nm | ||
| F03 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 125 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 7AZ | Toe arm to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. | 165 Nm |
| F03 | M14 | 110 Nm | |||
| 8AZ | Wishbone to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
280 Nm | ||
| 9AZ | Wishbone to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 90 Nm | ||||
| Angle of rotation | 180 ° | ||||
| F03 | M18 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 200 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 10AZ | Heat shield to toe arm | F01/F02 | M5 | Replace nut. | 6.8 Nm |
| 11AZ | Toe link bearing bracket to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screws and nuts. | 165 Nm |