51 16 Mirrors, Finishers, Ashtrays, Consoles
WARNING: This page is about a different variant/trim than selected.
TIGHTENING TORQUE SPECIFICATIONS - MIRRORS, FINISHERS, ASHTRAYS, CONSOLES
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Exterior mirror to front door | F01/F02/F03/F04/F07/F10/F11/F18 | thread cutting | 6 Nm | |
| New exterior mirror initial screw connection | 8 Nm | ||||
| F15/F16/F25/F26/F85/F86 | thread cutting | 9 Nm | |||
| New exterior mirror initial screw connection | 11 Nm | ||||
| F06/F12/F13 | thread cutting | 8 Nm | |||
| 2AZ | Sun visor to body | F01/F02/F03/F04/F07/F10/F11/F18/F25/F26 | 2.5 Nm | ||
| 3AZ | Grab handle, front/rear | F01/F02/F03/F04/F07/F10/F11/F18 | 3 Nm | ||
| 4AZ | Support, center console | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18/F25/F26 | 4.5 Nm | ||
| 5AZ | Floor trim panel to carrier | F01/F02/F03/F04 | 2.5 Nm | ||
| 6AZ | Decorative trim to center console/support | F01/F02/F03/F04/F06/F12/F13 | 1.2 Nm | ||
| 7AZ | Holder, center console, front, middle, to tunnel | F01/F02/F03/F04 | 4.5 Nm | ||
| 8AZ | Center console to instrument panel | F01/F02/F03/F04 | 2.5 Nm | ||
| 9AZ | Decorative trim to center console | F01/F02/F03/F04 | Dia. 5 mm | Oval-head screw for light alloy | 4 Nm |
| F01/F02/F03/F04 | TS5 x 12 | Plastic screw | 2.8 Nm | ||
| 10AZ | Center console/support to dashboard | F01/F02/F03/F04 | 2.5 Nm | ||
| F12/F13 | 1.2 Nm | ||||
| 11AZ | Trim, rear, with rear compartment nozzle | F01/F02/F03/F04 | 2.5 Nm | ||
| 12AZ | Rear console to body shell holder | F01/F02/F03/F04 | 6 Nm | ||
| 13AZ | Oddments tray, center armrest, to support, center console | F01/F02/F03/F04/F07 | 1.5 Nm | ||
| F06/F12/F13 | 1.2 Nm | ||||
| 14AZ | Handle to inner part, lid, glovebox | F01/F02/F03/F04/F25/F26 | 1.5 Nm | ||
| 15AZ | Lid, glove box/end cover to housing | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 1.5 Nm | ||
| 16AZ | Glove box/storage compartment to dashboard | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 1.8 Nm | ||
| F25/F26 | 2.4 Nm | ||||
| 17AZ | Guide rail, roller sunblind, B-pillar | F01/F02/F03/F04 | Self-tapping screw, black | 2 Nm | |
| F03 | Replace screws. | 2.5 Nm | |||
| 18AZ | Roller sunblind module | F01/F02/F04 | Oval flange head screw (ISA) | 3 Nm | |
| F03 | 8 Nm | ||||
| F06/F07/F10/F11/F18 | 1.5 Nm | ||||
| F25/F26 | 0.7 Nm | ||||
| 19AZ | Electric motor to function carrier | F01/F02/F04 | Flat-head screw | 4.4 Nm | |
| F03 | 8 Nm | ||||
| 20AZ | Engine to function carrier, top | F01/F02/F04 | Oval-head screw | 2 Nm | |
| F03 | 3 Nm | ||||
| 21AZ | Vent window guide rail - window bar connection | F03 | 4.6 Nm | ||
| 22AZ | Center console to support | F07 | 1.8 Nm | ||
| 23AZ | Bracket, handle, to bodyshell | F01/F02/F04 | 3 Nm | ||
| 24AZ | Support to holder, support part | F12/F13/F06 | 2.5 Nm | ||
| 25AZ | Side bracket to support | F06/F12/F13 | 1.2 Nm | ||