26 11 Propeller Shaft, complete
WARNING: This page is about a different variant/trim than selected.
TIGHTENING TORQUE SPECIFICATIONS - PROPELLER SHAFT COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Front flexible disc to transmission output flange ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 2AZ | Front flexible disk to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F85/F86/F18 PHEV/F15 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 3AZ | Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F36/F85/F86/F18 PHEV | ASA M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 4AZ | Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 5AZ | Centre mount to body | F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F85/F86/F18 PHEV/F15 PHEV | 21 Nm | ||
| 6AZ | Input flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01/F02/F03/F06/F07/F10/F11/F12/F13/F18 | Replace insert nut! Allow min. 2 hours hardening time | ||
| Jointing torque Loosen the insert nut through 90° |
120 Nm | ||||
| Tightening torque | 85 Nm | ||||
| F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F18/F85/F86 PHEV/F15 PHEV | 85 Nm | ||||
| 7AZ | Front propeller shaft to transfer box/front axle differential | F01/F02/F06/F07/F10/F11/F12/F13/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F36/F85/F86/F15 PHEV | Replace screws, jointing torque and angle of rotation must be observed without fail. | ||
| Jointing torque | 20 Nm | ||||
| Angle of rotation | 45 ° | ||||
| 8AZ | Constant velocity joint propeller shaft to rear axle differential | F06 M6/F10 M5/F12 M6/F13 M6 | M10 | Replace screws and shims, jointing torque and angle of rotation must be observed without fail. | |
| Jointing torque | 20 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 9AZ | Front propeller shaft to rear propeller shaft/constant velocity joint | F06 M6/F10 M5/F12 M6/F13 M6 | M12x1 | 60 Nm | |