64 52 Air conditioning compressor
WARNING: This page is about a different variant/trim than selected.
TIGHTENING TORQUE SPECIFICATIONS - AIR CONDITIONING COMPRESSOR
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Refrigerant lines to compressor | F01/F02/F03/F06/F07/F10/F10h/F11/F18/F12/F13/F15/F25 | M8 | 18 Nm | |
| F10/F11/F15/F16/F20/F21/F22/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83 | M6 | 8 Nm | |||
| 2AZ | Compressor oil filler plug | F01/F02/F03/F06/F07/F10/F11/F18/F12/F13/F15/F16/F25/F26/F20/F21/F22/F30/F31/F32/F33/F34/F35/F36/F45/F46/F55/F56/F80/F82/F83 | 30±1 Nm | ||
| 3AZ | Compressor to crankcase | N47T, F10/F11/F20/F15/F21/F22/F25/F26/F30/F31/F32/F33/F34/F36 | M10 | 38 Nm | |
| N13, F20/F21/F22/F30/F31 | M8 | 22 Nm | |||
| N20, F10/F11/F20/F21/F22/F25/F26/F30/F31/F33/F34/F32/F35/F36 | M10 | 38 Nm | |||
| N54, F01/F02 | M8 | 19 Nm | |||
| N55, F06/F07/F10/F10h/F11/F15/F16/F18/F12/F13/F20/F21/F22/F26/F25/F30/F31/F32/F33/F34/F35/F36 | M8 | 19 Nm | |||
| N57, F01/F02/F07/F10/F11 | M8 | 19 Nm | |||
| N57, F06/F07/F10/F11/F12/F13/F15/F16/F26/F25/F30/F32/F31/F33/F34/F36 | M10 | 38 Nm | |||
| N63, F01/F02/F03/F04/F06/F07/F10/F11/F12/F13 | M8 | 21±3 Nm | |||
| N63T, F15/F16 | M8 | 24.6 Nm | |||
| N74, F01/F02/F03 | M8 | 21±3 Nm | |||
| F45/F46/F55/F56 All | M10 | 38 Nm | |||
| B47, F20/F21/F22/F23/F25/F26 | M10 | 38 Nm | |||
| B37, F20/F21 | M10 | 38 Nm | |||
| B38, F20/F21/F22/F23/F30/F31 | M10 | 38 Nm | |||
| S55, F80/F82/F83 | M8 | 19 Nm | |||
| S63, F85/F86 | M8 | 24.6 Nm | |||
| N52, F01/F02/F10/F11/F18/F25 | M8 | Replace screws. | |||
| Torque: | 10 Nm | ||||
| Angle of rotation: | 180 ° | ||||
| 4AZ | Refrigerant lines to compressor | F04 | M6 | 10±2 Nm | |
| 5AZ | Compressor holder to lower crankcase section | N55, F20/F21/F22/F23/F30/F32/F31/F33/F35/F36 | 19 Nm | ||
| 6AZ | Refrigerant lines to component carrier | F10h | M6 | 8 Nm | |
| 7AZ | Holder for refrigerant lines to compressor | N57X, F10/F11 | M6 | 8 Nm | |