51 61 Reinforcement, body
WARNING: This page does not describe the selected car, but rather 21 other vehicles, including the 2017 BMW 550i GT xDrive, 2017 BMW 535i GT xDrive, 2017 BMW 535i GT, 2016 BMW 550i GT xDrive, and 2016 BMW 535i GT xDrive. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - REINFORCEMENT, BODY
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Suspension cross-brace in engine compartment, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Replace screws | |
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F15/F16 | Replace screws | ||||
| Jointing torque | 25 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F25/F26 | M10x25 | Replace screws | |||
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 2AZ | Suspension cross-brace in engine compartment, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x25 | 56 Nm | |
| F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Replace screws | |||
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 3AZ | Connection, rear, to carrier support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 28 Nm | ||
| 4AZ | Connection, front, to connection, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 5AZ | Engine compartment lid catch | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8x20 | 11.8 Nm | |
| 6AZ | V-support to connection, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 7AZ | Air duct, lower, to vertical strut | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 8AZ | Air duct, lower, to carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 9AZ | Air duct, upper, on lock support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 10AZ | Trailing link/V-strut on side member | F07/F11/F12/F13 | M12 | Replace screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 11AZ | Trailing link to compression strut, rear axle | F07/F11/F12 | M8 | 19 Nm | |
| 12AZ | Trailing link to cross reinforcement (rear end support) | F07/F11/F12 | M12x1.5x53 | Replace screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 13AZ | Cross reinforcement (support, rear end) to rear end | F07/F11/F12 | M10x22 | 38 Nm | |
| 14AZ | Cross reinforcement (support, rear end) to cross-member | F07/F11/F12 | M10 | 38 Nm | |
| 15AZ | Torsion struts/stiffening plate to front axle support | F01/F02/F03/F12 | M10 | Replace screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 16AZ | Rear trailing link | F10/F12 | M10x40 | Replace screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 105 ° | ||||
| 17AZ | Rear trailing link | F10/F12 | M8x35 | Replace screws | |
| Jointing torque | 28 Nm | ||||
| Angle of rotation | 90 ° | ||||