33 32 Trailing arms and struts
WARNING: This page does not describe the selected car, but rather 21 other vehicles, including the 2017 BMW 550i GT xDrive, 2017 BMW 535i GT xDrive, 2017 BMW 535i GT, 2016 BMW 550i GT xDrive, and 2016 BMW 535i GT xDrive. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - TRAILING ARMS AND STRUTS
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Swinging arm/cross-strut to rear axle support, front | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION |
|
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace screw and nut. | 100 Nm | ||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 2AZ | Swinging arm to rear axle support, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION |
175 Nm |
| F03 | M18 | Replace eccentric bolt, eccentric washer and nut. TIGHTEN DOWN IN NORMAL POSITION |
|||
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 3AZ | Swinging arm to wheel carrier, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M16 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION |
265 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION |
|||
| Jointing torque | 360 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 4AZ | Swinging arm/integral link | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. | |
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 45 ° | ||||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 5AZ | Integral link to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | 108 Nm | |
| F03 | M16 | 250 Nm | |||
| 6AZ | Toe arm to bearing support/to Integral Active Steering | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION |
|
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace nut. | 100 Nm | ||
| F03 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION |
|||
| Jointing torque | 125 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 7AZ | Toe arm to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. | 165 Nm |
| F03 | M14 | 110 Nm | |||
| 8AZ | Wishbone to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION |
175 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION |
280 Nm | ||
| 9AZ | Wishbone to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION |
|
| Jointing torque | 90 Nm | ||||
| Angle of rotation | 180 ° | ||||
| F03 | M18 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 200 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 10AZ | Heat shield to toe arm | F01/F02 | M5 | Replace nut. | 6.8 Nm |
| 11AZ | Toe link bearing bracket to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screws and nuts. | 165 Nm |