26 11 Propeller Shaft, complete
WARNING: This page does not describe the selected car, but rather 21 other vehicles, including the 2017 BMW 550i GT xDrive, 2017 BMW 535i GT xDrive, 2017 BMW 535i GT, 2016 BMW 550i GT xDrive, and 2016 BMW 535i GT xDrive. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - PROPELLER SHAFT COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Front flexible disc to transmission output flange ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F18 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 2AZ | Front flexible disk to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F80/F82/F83/F18 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 3AZ | Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F22/F23/F30/F31/F32/F33/F34/F36/F18 PHEV | ASA M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 4AZ | Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts, jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01/F02/F03/F06/F07/F10/F11/F12/F13/F18/F20/F21/F22/F23/F30/F31/F32/F33/F34/F35/F36/F18 PHEV | M12-10.9 | Jointing torque | 55 Nm | ||
| Angle of rotation | 90 ° | ||||
| 5AZ | Centre mount to body | F01/F02/F03/F06/F07/F10/F11/F12/F13/F15/F16/F18/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F18 PHEV | 21 Nm | ||
| 6AZ | Drive flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01/F02/F03/F06/F07/F10/F11/F12/F13/F18 | Replace insert nut! Allow min. 2 hours hardening time | ||
| Jointing torque Loosen the insert nut through 90° |
120 Nm | ||||
| Tightening torque | 85 Nm | ||||
| F15/F16/F20/F22/F23/F25/F26/F30/F31/F32/F33/F34/F35/F36/F18 PHEV | 85 Nm | ||||
| 7AZ | Front propeller shaft to transfer box/front axle differential | F01/F02/F06/F07/F10/F11/F12/F13/F15/F16/F20/F21/F22/F23/F25/F26/F30/F31/F32/F33/F34/F36 | Replace screws, jointing torque and angle of rotation must be observed without fail. | ||
| Jointing torque | 20 Nm | ||||
| Angle of rotation | 45 ° | ||||
| 8AZ | Constant velocity joint propeller shaft to rear axle differential | F06 M6/F10 M5/F12 M6/F13 M6 | M10 | Replace screws and shims, jointing torque and angle of rotation must be observed without fail. | |
| Jointing torque | 20 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 9AZ | Front propeller shaft to rear propeller shaft/constant velocity joint | F06 M6/F10 M5/F12 M6/F13 M6 | M12x1 | 60 Nm | |