51 61 Reinforcement, body
WARNING: This page is about a different car, the 2013 BMW 550i GT, 2012 BMW 550i GT, 2011 BMW 550i GT, and 2010 BMW 550i GT. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - REINFORCEMENT, BODY
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Suspension cross-brace, rear | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M10x47 | Replace screws | |
| Jointing torque | 30 Nm | |||
| Angle of rotation | 90 ° | |||
| F25 | M10x25 | Replace screws | ||
| Jointing torque | 56 Nm | |||
| Angle of rotation | 90 ° | |||
| 2AZ Suspension cross-brace, front | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M10x25 | 56 Nm | |
| F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M10x47 | Replace screws | ||
| Jointing torque | 30 Nm | |||
| Angle of rotation | 90 ° | |||
| 3AZ Connection, rear, to carrier support | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | 28 Nm | ||
| 4AZ Connection, front, to connection, rear | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | 19 Nm | ||
| 5AZ Engine compartment lid catch | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M8x20 | 11.8 Nm | |
| 6AZ V-support to connection, front | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | 19 Nm | ||
| 7AZ Air duct, lower, to vertical strut | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | 19 Nm | ||
| 8AZ Air duct, lower, to carrier | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M8 | 8 Nm | |
| 9AZ Air duct, upper, on lock support | F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 | M8 | 8 Nm | |
| 10AZ Trailing link/V-strut on side member | F07 / F11 / F12 / F13 | M12 | Replace screws | |
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90 ° | |||
| 11AZ Trailing link to compression strut, rear axle | F07 / F11 / F12 | M8 | 19 Nm | |
| 12AZ Trailing link to cross reinforcement (rear end support) | F07 / F11 / F12 | M12x1.5x53 | Replace screws | |
| Jointing torque | 100 Nm | |||
| Angle of rotation | 90 ° | |||
| 13AZ Cross reinforcement (support, rear end) to rear end | F07 / F11 / F12 | M10x22 | 38 Nm | |
| 14AZ Cross reinforcement (support, rear end) to cross-member | F07 / F11 / F12 | M10 | 38 Nm | |
| 15AZ Torsion struts/stiffening plate to front axle support | F01 / F02 / F03 / F12 | M10 | Replace screws | |
| Jointing torque | 56 Nm | |||
| Angle of rotation | 90 ° | |||
| 16AZ Rear trailing link | F10 / F12 | M10x40 | Replace screws | |
| Jointing torque | 56 Nm | |||
| Angle of rotation | 105 ° | |||
| 17AZ Rear trailing link | F10 / F12 | M8x35 | Replace screws | |
| Jointing torque | 28 Nm | |||
| Angle of rotation | 90 ° |