11 31... Service solution - replacing intake camshaft (N20)

Special tools required:

11 7 110 .
11 4 481 .

WARNING: Risk of injury in event of incorrect use.

IMPORTANT: Improper handling. Risk of damage.

Necessary preliminary tasks:

Removal:

NOTE: Injector shafts shown removed for purposes of clarity.

IMPORTANT: Secure eccentric shaft (1) with open-end spanner (3) (risk of return stroke).

Slowly adjust eccentric shaft (1) to minimum lift via servomotor using 4-mm hexagon socket wrench (2) and open-end spanner (3).

Fig 1: Adjusting Eccentric Shaft

Courtesy of BMW OF NORTH AMERICA, INC.

Release bolt (1) on the oil spray nozzle.

Tightening torque 11 37 4AZ .

Unclip oil spray nozzle (2) from the bracket on the actuator drive (3) in direction of arrow.

Fig 2: Unclipping Oil Spray Nozzle

Courtesy of BMW OF NORTH AMERICA, INC.

Position special tool 11 7 110 on return spring (1) (see arrows).

Fig 3: Positioning Special Tool 11 7 110 On Return Spring

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Risk of injury in event of incorrect use.

IMPORTANT: Improper handling. Risk of damage.

Place special tool 11 7 110 flat on cylinder head.

Turn knurled screw (1) in direction of arrow until both clamping levers secure return spring in gate.

Fig 4: Turning Knurled Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Return spring is correctly preloaded when both clamping levers are parallel to guide block.

Fig 5: Identifying Clamping Levers Of Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Risk of damage.

Left and right return springs (1) must be positioned in lateral guide of special tool 11 7 110 .

Fig 6: Identifying Special Tool (11 7 110) And Return Spring

Courtesy of BMW OF NORTH AMERICA, INC.

Preload return spring with lever (1) on special tool 11 7 110 in direction of arrow.

Fig 7: Identifying Lever And Special Tool (11 7 110)

Courtesy of BMW OF NORTH AMERICA, INC.

Lock special tool 11 7 110 with catch on lever (1).

IMPORTANT: Screw connection on throttle return spring can only be released with secured special tool 11 7 110 .

Fig 8: Locking Special Tool (11 7 110) With Catch On Lever

Courtesy of BMW OF NORTH AMERICA, INC.

Release screw (1).

Fig 9: Releasing Screw

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Risk of injury in event of incorrect use.
Lever (1) is preloaded.

IMPORTANT: Improper handling. Risk of damage.

Secure lever (1).

Press back latching hook (2).

Return spring tension can now be released.

Fig 10: Releasing Return Spring Tension

Courtesy of BMW OF NORTH AMERICA, INC.

Release knurled screw (1) on special tool 11 7 110 in direction of arrow.

Fig 11: Releasing Knurled Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Release special tool 11 7 110 in direction of arrow from return spring (1).

Fig 12: Removing Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Return springs (1) remain on the engine.

Fig 13: Identifying Return Springs

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: All bearing caps are identified with numbers from 1 to 4.

The front bearing cap is a thrust bearing and does not have an identification.

Release screws on all bearing caps (1 to 10).

Set down all bearing caps in a tidy and orderly fashion on special tool 11 4 481 .

Fig 14: Right Intake Camshaft Bearing Cap Bolts Tightening/Loosening Sequence (N20)

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Do not remove intermediate levers (1). Mixing up the intermediate levers (1) will cause the engine to suffer idle-speed fluctuations.

Remove intake camshaft.

Fig 15: Identifying Intermediate Levers

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

IMPORTANT: Marks of intake and exhaust camshafts different.
Mixing up the intake and exhaust cams result in engine damage .
A Exhaust camshaft.
E Intake camshaft

Fig 16: Identifying Exhaust (A) And Intake (E) Camshafts

Courtesy of BMW OF NORTH AMERICA, INC.

Insert intake camshaft so that data code (1) on mounting flats points upwards.

Fig 17: Locating Camshaft Designation

Courtesy of BMW OF NORTH AMERICA, INC.

Position intake camshaft so that cams point downward at an angle and to the left.

Fig 18: Positioning Intake Camshaft With Cams Pointing Downward At Angle Toward Left

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: All bearing caps are identified with numbers from 1 to 4.

The front bearing cap is a thrust bearing and does not have an identification.

Insert screws on all bearing caps from (10) to (1).

Tightening torque 11 31 3AZ .

Fig 19: Right Intake Camshaft Bearing Cap Bolts Tightening/Loosening Sequence (N20)

Courtesy of BMW OF NORTH AMERICA, INC.

Position special tool 11 7 110 on return spring.

Fig 20: Removing Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Clamp throttle return spring with knurled screw (1) in direction of arrow.

Fig 21: Turning Knurled Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Return spring (1) is positioned correctly when latching hooks surround return spring (1).

Fig 22: Identifying Return Spring

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Risk of injury in event of incorrect use.

IMPORTANT: Improper handling. Risk of damage.
Check return spring on intermediate lever to ensure correct installation position.

Press special tool 11 7 110 to stop in direction of arrow.

Fig 23: Pressing Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Install return spring (2) on gate.

IMPORTANT: Insert return spring (2) in intermediate lever (1) (see arrow).
Check that rocker arm (3) is in correct installation position.

Fig 24: Inserting Return Spring In Intermediate Lever And Checking Rocker Arm Installation Position

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Check that intermediate lever (1) is installed in correct position on eccentric shaft (2).

Fig 25: Identifying Intermediate Lever And Eccentric Shaft

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Observe thread on cylinder head. Risk of damage.

Tighten bolt (1).

Tightening torque 11 37 2AZ .

Fig 26: Releasing Screw

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Risk of injury in event of incorrect use.
Lever (1) is preloaded.

IMPORTANT: Improper handling. Risk of damage.

Secure lever (1).

Press back latching hook (2).

Fig 27: Releasing Return Spring Tension

Courtesy of BMW OF NORTH AMERICA, INC.

Return spring tension can now be released.

Check installation position of intermediate lever and return spring again , remove special tool 11 7 110 .

Retract oil spray nozzle (2) on actuator drive (3).

Engage bolt (1) and release back to 90°.

For exact positioning of the oil spray nozzle (2) audibly clip it in at the top.

Tightening torque 11 37 4AZ .

Fig 28: Unclipping Oil Spray Nozzle

Courtesy of BMW OF NORTH AMERICA, INC.

Required follow-up work:

Install INTAKE CAMSHAFT ADJUSTER .

Adjust VALVE TIMING .

Fit CYLINDER HEAD COVER .

Install DME CONTROL UNIT .