LEMON Manuals: Even more car manuals for everyone
Home >> BMW >> 2014 >> 435i xDrive Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Body Equipment - Repair - F32 >> Mirrors/Covers/Ashtrays/Shelves/Trays >> 51 16 160 Uninstall and install trim center console >> Procedure steps

Procedure steps

safety instructions 

RISK OF DAMAGE 

Scratches. 

Tools and sharp-edged components can cause scratches.

Preprocesses 

  1. - Remove decorative trim on center console 
    • For equipment specification with in leather instrument panel: Attach plastic adhesive tape (2) between decorative trim (1) and instrument panel.
      Fig 1: Instrument Panel Decorative Strip And Adhesive Tape
      G10096954Courtesy of BMW OF NORTH AMERICA, INC.
    • Detach decorative trim (1) with special tool 0 496 571 (00 9)  clamps (2).
    • If necessary, unlock associated plug connections and disconnect.
    • Remove decorative trim (1) upwards.
      Fig 2: Loosening Center Console Cover With Special Tool (00 9 327) From Clamps
      G10096955Courtesy of BMW OF NORTH AMERICA, INC.
  2. - Remove trim for selector lever 
    • Partially fit special tool 0 493 687 (00 9 340)  as pictured.
    • Lift trim for selector lever (1) all around and remove upwards.
    • If necessary, unlock associated plug connection and disconnect.
      Fig 3: Installing Special Tool (00 9 340)
      G10097004Courtesy of BMW OF NORTH AMERICA, INC.
  3. - Removing the operating unit for the center console 
    • Adhere to following procedure:
      1. Reach under front section of operating unit for the center console (1).
      2. Press front latch mechanism in direction of arrow and simultaneously raise operating unit for the center console top.
      3. Disconnect associated plug connection and remove for the center console (1).
        Fig 4: Removing Center Console Operating Unit
        G10098505Courtesy of BMW OF NORTH AMERICA, INC.

    Key processes 

  4. - Removing the trim for the center console 
    • Loosen screws (1).
    • Detach trim for center console (2) with special tool 0 496 569 (00 9 325)  for clamps (3).
    • Slightly raise trim for center console (2) and disconnect associated plug connections.
    • Guide out trim for center console (2) to the top/rear.
      Fig 5: Center Console Cover, Clamps And Screw
      G10096989Courtesy of BMW OF NORTH AMERICA, INC.
  5. - Installing the trim for the center console 
    • Do not detach springs (1) during installation.
    • Replace faulty clamps.
      Fig 6: Center Console Clamps
      G10153417Courtesy of BMW OF NORTH AMERICA, INC.
    • Connect all plug connections.
    • Position trim for center console (2).
    • Clip in trim for center console (2) at latch mechanisms
    • Tighten the screws (1).
      Fig 7: Center Console Cover, Clamps And Screw
      G10096989Courtesy of BMW OF NORTH AMERICA, INC.

    Post processes 

  6. - Installing the operating unit for the center console 
    • Clip in the operating unit f or the center console.
      Fig 8: Removing Center Console Operating Unit
      G10098505Courtesy of BMW OF NORTH AMERICA, INC.
  7. - Install trim for selector lever 

    TECHNICAL INFORMATION 

    Latch mechanisms, guides and mounting elements must damaged or missing.

    Fig 9: Selector Lever Latch Mechanisms And Cover
    G10097005Courtesy of BMW OF NORTH AMERICA, INC.
    • Check latch mechanisms for damage, if necessary replace trim for selector lever.
    • Clip in trim for selector lever (1).
      Fig 10: Installing Special Tool (00 9 340)
      G10097004Courtesy of BMW OF NORTH AMERICA, INC.
  8. - Installing the decorative trim to center console 

    TECHNICAL INFORMATION 

    The controller may have to be remounted upon replacing the decorative trim, depending on the equipment specification.

    For more information see: 61 31 195 REMOVING AND INSTALLING/REPLACING CONTROLLER

    • Replace faulty clamps (1) of the decorative trim (2).
      Fig 11: Controller Clamps
      G10096956Courtesy of BMW OF NORTH AMERICA, INC.
    • For equipment specification with in leather instrument panel: Attach plastic adhesive tape (2) between decorative trim (1) and instrument panel.
      Fig 12: Instrument Panel Decorative Strip And Adhesive Tape
      G10096954Courtesy of BMW OF NORTH AMERICA, INC.
    • Clip in the decorative trim (1) at the latch mechanisms
      Fig 13: Loosening Center Console Cover With Special Tool (00 9 327) From Clamps
      G10096955Courtesy of BMW OF NORTH AMERICA, INC.