26 11 Propeller Shaft
WARNING: This page is about a different car, the 2011 BMW Z4, 2010 BMW Z4, and 2009 BMW Z4. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 5AZ | Pivot fork piece to centre propeller shaft bearing journal with Loctite (Version without sliding piece) | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | 97 Nm | ||
| 6AZ | Centre mount to body | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E84/E88/E89 | 21 Nm | ||
| 7AZ | Flexible disc to front axle differential | E53 | M10-10.9 | 60 Nm | |
| 8AZ | Flexible disc on propeller shaft | E53 | M10-10.9 | 64 Nm | |
| 9AZ | Front propeller shaft to transfer box/front axle differential ZNS screws and nuts, shiny zinc coating | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | |||
| E60/E61/E90/E91/E92/E84/E70/E71 | M8 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10-10.9 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E53/E70/E71/E72 | M10-12.9 | Jointing torque | 10 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10x1.5 10.9 | Jointing torque | 5 Nm | ||
| Angle of rotation | 90 ° | ||||
| Universal joint | E70/E71/E72/E83 | M10-10.9 | Jointing torque | 40 Nm | |
| Angle of rotation | 45° | ||||
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Propeller shaft plugged into rear axle final drive (insert nut) | E9x/E82N54/E82N55/E88N54/E90/E91/E92M57T2/Top/E89/E84 N52K/E70/E71/E72 | Torque | 75 Nm | |
| 2AZ | Propeller shaft plugged into rear axle final drive with universal joint (insert nut) | F25 | Torque | 75 Nm | |
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specification | Measure | ||
|---|---|---|---|---|---|
| Flexible disc to transmission output flange ZNS screws and nuts Shiny zinc coating All versions |
Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | ||||
| E60/E61/E63/E64/E85/E86/E87/E90/E91/E92/E93/E81/E82/E83/E84/E88/E89 | M10-10.9 | Jointing torque | 20 Nm | ||
| Torque angle | 90 ° | ||||
| E46/E53/E60/E61/E63/E64/E65/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E83/E84/E88/E89 | M12-10.9 | Jointing torque | 55 Nm | ||
| Torque angle | 90 ° | ||||
| E60/E61/E63/E64/E65 | M12-8.8 | Jointing torque | 30 Nm | ||
| Torque angle | 90 ° | ||||
| E83 | M12-10.9 | Jointing torque | 30 Nm | ||
| Torque angle Screw with ribbed teeth + double stage flexible disc | 90 ° | ||||
| 2AZ | Coupling propeller shaft to transmission | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 | 60 Nm | |
| E32/E31 | M12 | 95 Nm | |||