33 32 Trailing arms and struts
TIGHTENING TORQUE SPECIFICATION - TRAILING ARMS AND STRUTS
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Swinging arm/cross-strut to rear axle support, front | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
165 Nm 90 ° |
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace screw and nut. | 100 Nm | |
| F03 | M16 | Replace screw and nut. | 250 Nm | |
| 2AZ Swinging arm to rear axle support, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace eccentric bolt, eccentric washer and nut. TIGHTEN DOWN IN NORMAL POSITION . |
||
| Jointing torque | 100 Nm | |||
| Angle of rotation | 180 ° | |||
| 3AZ Swinging arm to wheel carrier, rear | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M16 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
265 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
360 Nm 180 ° |
|
| 4AZ Swinging arm/integral link | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. Jointing torque Angle of rotation |
165 Nm 45 ° |
| F03 | M16 | Replace screw and nut. | 250 Nm | |
| 5AZ Integral link to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | 108 Nm | |
| F03 | M16 | 250 Nm | ||
| 6AZ Toe arm to bearing support/to Integral Active Steering | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M12 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
100 Nm 90 ° |
| F06 M6/F10 M5/F12 M6/F13 M6 | M12 | Replace nut. | 100 Nm | |
| F03 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
125 Nm 90 ° |
|
| 7AZ Toe arm to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. | 165 Nm |
| F03 | M14 | 110 Nm | ||
| 8AZ Wishbone to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
280 Nm | |
| 9AZ Wishbone to wheel carrier | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
90 Nm 180 ° |
| F03 | M18 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . Jointing torque Angle of rotation |
200 Nm 180 ° |
|
| 10AZ Heat shield to toe arm | F01/F02 | M5 | Replace nut. | 6.8 Nm |
| 11AZ Toe link bearing bracket to rear axle support | F01/F02/F04/F06/F07/F10/F11/F12/F13/F18 | M14 | Replace screws and nuts. | 165 Nm |