26 11 Propeller Shaft, complete
WARNING: This page is about a different car, the 2011 BMW 750xi, 2011 BMW 750Lxi, 2010 BMW 750xi, and 2010 BMW 750Lxi. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 1AZ Front flexible disc to transmission output flange ZNS screws and nuts All versions |
Replace screws and nuts; jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01 / F02 / F03 / F06 / F07 / F10 / F11 / F12 / F13 / F18 / F20 / F21 / F25 / F30 / F31 / F35 | M12-10.9 | Jointing torque | 55 Nm | |
| Angle of rotation | 90 ° | |||
| 2AZ Front flexible disk to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts; jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01 / F02 / F03 / F07 / F10 / F11 / F12 / F13 / F18 / F20 / F21 / F25 / F30 / F31 / F35 | M12-10.9 | Jointing torque | 55 Nm | |
| Angle of rotation | 90 ° | |||
| 3AZ Flexible disc, rear, to transmission drive flange (inserted) ZNS screws and nuts All versions |
Replace screws and nuts; jointing torque and angle of rotation must be observed without fail. Tightening via screw |
|||
| F01 / F02 / F03 / F06 / F07 / F10 / F11 / F12 / F13 / F18 / F20 / F30 / F31 | ASA M12-10.9 | Jointing torque | 55 Nm | |
| Angle of rotation | 90 ° | |||
| 4AZ Flexible disc, rear, to propeller shaft ZNS screws and nuts All versions |
Replace screws and nuts; jointing torque and angle of rotation must be observed without fail. Tighten via nut |
|||
| F01 / F02 / F03 / F06 / F07 / F10 / F11 / F12 / F13 / F18 / F20 / F21 / F30 / F31 / F35 | M12-10.9 | Jointing torque | 55 Nm | |
| Angle of rotation | 90 ° | |||
| 5AZ Centre mount to body | F01 / F02 / F03 / F06 / F07 / F10 / F11 / F12 / F13 / F18 / F20 / F21 / F25 / F30 / F31 / F35 | 21 Nm | ||
| 6AZ Drive flange, rear axle final drive (insert nut to propeller shaft/three-hole flange) | F01 / F02 / F03 / F07 / F10 / F11 / F12 / F13 / F18 | Replace insert nut! Allow min. 2 hours hardening time | ||
| Jointing torque Loosen the insert nut through 90° |
120 Nm | |||
| Tightening torque | 85 Nm | |||
| F20 / F25 / F30 / F31 / F35 | 85 Nm | |||
| 7AZ Front propeller shaft to transfer box/front axle differential | F01 / F02 / F07 / F10 / F11 / F12 / F13 / F20 / F21 / F25 / F30 | Replace screws; jointing torque and angle of rotation must be observed without fail. | ||
| Jointing torque | 20 Nm | |||
| Angle of rotation | 45 ° | |||
| 8AZ Constant velocity joint propeller shaft to rear axle differential | F10 S63 | Renew screws and shims; jointing torque and angle of rotation must be observed without fail. | ||
| Jointing torque | 20 Nm | |||
| Angle of rotation | 90 ° | |||
| 9AZ Front propeller shaft to rear propeller shaft/constant velocity joint | F10 S63 | M12x1 | 60 Nm |