51 61 Reinforcement, body
TIGHTENING TORQUE SPECIFICATIONS - REINFORCEMENT, BODY
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Suspension cross-brace in engine compartment, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws | |
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F15/F16 | Renew screws | ||||
| Jointing torque | 25 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F25/F26 | M10x25 | Renew screws | |||
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 2AZ | Suspension cross-brace in engine compartment, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x25 | 56 Nm | |
| F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws | |||
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 3AZ | Connection, rear, to carrier support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 28 Nm | ||
| 4AZ | Connection, front, to connection, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 5AZ | Engine compartment lid catch | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8x20 | 11.8 Nm | |
| 6AZ | V-support to connection, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 7AZ | Air duct, lower, to vertical strut | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 8AZ | Air duct, lower, to carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 9AZ | Air duct, upper, on lock support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 10AZ | Trailing link/V-strut on side member | F07/F11/F12/F13 | M12 | Renew screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 11AZ | Trailing link to compression strut, rear axle | F07/F11/F12 | M8 | 19 Nm | |
| 12AZ | Trailing link to cross reinforcement (rear end support) | F07/F11/F12 | M12 | Renew screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 13AZ | Cross reinforcement (support, rear end) to rear end | F07/F11/F12 | M10x22 | 38 Nm | |
| 14AZ | Cross reinforcement (support, rear end) to cross-member | F07/F11/F12 | M10 | 38 Nm | |
| 15AZ | Torsion struts/stiffening plate to front axle support | F01/F02/F03/F12 | M10 | Renew screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 16AZ | Rear trailing link | F10/F12 | M10x40 | Renew screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 105 ° | ||||
| 17AZ | Rear trailing link | F10/F12 | M8x35 | Renew screws | |
| Jointing torque | 28 Nm | ||||
| Angle of rotation | 90 ° | ||||