13 53 192 Removing and installing/replacing a pressure line (N53, N54, N54T)
Special tools required:
Disconnect NEGATIVE BATTERY TERMINAL (risk of fire due to short circuit on dismantling).
Electric fuel pump starts up automatically when door is opened!
Carry out installation work on fuel system only with coolant temperature below 40 °C.
Fuel can emerge spontaneously at high speed when the high pressure line is released!
Introduced contaminants can cause malfunctions in the system!
- Do not allow any dirt particles or foreign bodies to get into the system.
- Remove all traces of dirt contamination before removing lines or separate components.
- Use only fluff-free cloths.
- Seal all fuel system openings with protective caps or plugs.
- High pressure lines may be re-screwed a maximum of 10 times.
Necessary preliminary tasks:
- Remove IGNITION COIL of corresponding cylinder.
- Ignition coils must not be fouled by fuel!
The resistance of the silicone material is reduced significantly by contact with fuel, which may cause the ignition coil to fail! It is therefore essential to protect the spark plug slot against ingress of fuel with a cloth!
- Before installing ignition coils, clean spark plug slots with compressed air.
- Make sure the spark plug slot is absolutely clean.
Recycling
Fuel escapes when fuel lines are detached.
Catch and dispose of escaping fuel in a suitable container.
Observe country-specific waste disposal regulations.
Fuel can emerge spontaneously at high velocity from the fuel injectors!
To reduce the fuel pressure, place rag over fuel injector and carefully tap against the fuel injector with a spanner.
There is a risk of injury if the fuel pressure is not reduced!
First disconnect the pressure lines from the rail. To reduce existing fuel pressure if necessary. Fuel must not get into the spark plug slot. Then disconnect the pressure line from the injector.
Release nuts (1), gripping the injector with a spanner (2) in so doing.
Disconnect pressure line (3).
Mark pressure lines.
Close off injector with protective cap (1).
Protective caps are available from BMW Parts Service.
Seal high pressure rail with appropriate plug from set of special tools 32 1 270 .
Seal pressure line (1) with a matching plug from set of special tools 32 1 270 .
Installing pressure line
Installation of pressure line is described separately from removal.
Same procedure for all pressure lines.
Copper seals that may be fitted (1) are no longer needed and must be removed.
If reusing the pressure line, apply a light coating of transmission oil to the thread. New pressure lines are already coated.
To ensure distortion-free installation of the pressure line and to avoid damaging the thread, it must be possible for both nuts to be screwed on easily by hand!
If the nuts cannot be easily screwed on by hand, the injector must be turned into the installation position!
Only if injector has to be rotated in fitted position
- Release bolt a few turns until holding-down device (1) is slackened.
- Turn injector (2) in direction of arrow until nuts on pressure line can be easily screwed on by hand.
- To do so, engage spanner on hexagon head of injector if necessary.
- Tighten nuts on pressure line hand-tight.
If the injector is pulled out of the bore hole, the PTFE sealing ring must be replaced! Replacing PTFE sealing ring, refer to 13 53 310 REMOVING AND INSTALLING/REPLACING AN INJECTOR (N55) .
Tighten down screw for hold-down device (1).
Tightening torque: 13 53 5AZ (N54) or 13 53 5AZ (N55).
Adhere to tightening sequence:
- First tighten down nut (1) on injector.
- Then tighten down nut (2) on high-pressure rail.
When tightening nut (1) on injector, grip hexagon head of injector with wrench (3).
Tighten down nuts with special tool 37 1 151 .
Tightening torque: 13 53 8AZ .
Assemble engine.
Check fuel system for tightness.
Check function of DME.