24 1 Transmission in general
TIGHTENING TORQUE SPECIFICATIONS - TRANSMISSION IN GENERAL
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Transmission to engine | ||||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | 24 Nm | ||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M10 | 45 Nm | ||
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M12 | 82 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M8 | 21 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M10 | 42 Nm | ||
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M12 | 72 Nm | ||
| Torx bolts | GA6HP19Z/GA6HP26Z | M6 | 9 Nm | ||
| Torx bolts | GA6HP26Z | M10 | 38 Nm | ||
| Steel Torx screws | GA6HP19Z/GA6L26Z/GA6L45R | M8 | 19 Nm | ||
| Steel Torx screws | GA6HP19Z/GA6HP26Z/GA6L45R | M12 | 66 Nm | ||
| 2AZ | Transmission to engine N51/N52/N52K/N53/N54/N55 Aluminum screws are not magnetic | GA6HP19Z/GA6HP26Z/GA6L45R | Replace screws Jointing torque and angle of rotation must be observed without fail | ||
| GA6HP19Z/GA6L45R | M10x30 | Jointing torque | 20 Nm | ||
| Angle of rotation | 90-110 ° | ||||
| GA6HP19Z | M10x85 | Jointing torque | 20 Nm | ||
| Angle of rotation | 180-200 ° | ||||
| GA6HP19Z/GA6L45R | M12 | Jointing torque | 25 Nm | ||
| Angle of rotation | 130 ° | ||||
| 3AZ | Reinforcement shell to transmission/extension | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | 23 Nm | |
| 4AZ | Cover plate for transmission | GA6HP19Z/GA6L45R | M6 | 9 Nm | |
| 5AZ | Heat shield, oil sump | GA6L45R/GA6HP19Z | M6 | 8 Nm | |
| 6AZ | Air duct plate | GA6HP26Z | M6 | 10 Nm | |
| 7AZ | Line cover plate | GA6HP26Z | M6 | 10 Nm | |