26 11 Propeller Shaft
WARNING: This page is about a different variant/trim than selected.
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 5AZ | Pivot fork piece to centre propeller shaft bearing journal with Loctite (Version without sliding piece) | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | 97 Nm | ||
| 6AZ | Centre mount to body | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E84/E88/E89 | 21 Nm | ||
| 7AZ | Flexible disc to front axle differential | E53 | M10-10.9 | 60 Nm | |
| 8AZ | Flexible disc on propeller shaft | E53 | M10-10.9 | 64 Nm | |
| 9AZ | Front propeller shaft to transfer box/front axle differential ZNS screws and nuts, shiny zinc coating | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | |||
| E60/E61/E90/E91/E92/E84/E70/E71 | M8 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10-10.9 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E53/E70/E71/E72 | M10-12.9 | Jointing torque | 10 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10x1.5 10.9 | Jointing torque | 5 Nm | ||
| Angle of rotation | 90 ° | ||||
| Universal joint | E70/E71/E72/E83 | M10-10.9 | Jointing torque | 40 Nm | |
| Angle of rotation | 45° | ||||
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Propeller shaft plugged into rear axle final drive (insert nut) | E9x/E82N54/E82N55/E88N54/E90/E91/E92M57T2/Top/E89/E84 N52K/E70/E71/E72 | Torque | 75 Nm | |
| 2AZ | Propeller shaft plugged into rear axle final drive with universal joint (insert nut) | F25 | Torque | 75 Nm | |
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specification | Measure | ||
|---|---|---|---|---|---|
| Flexible disc to transmission output flange ZNS screws and nuts Shiny zinc coating All versions |
Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | ||||
| E60/E61/E63/E64/E85/E86/E87/E90/E91/E92/E93/E81/E82/E83/E84/E88/E89 | M10-10.9 | Jointing torque | 20 Nm | ||
| Torque angle | 90 ° | ||||
| E46/E53/E60/E61/E63/E64/E65/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E83/E84/E88/E89 | M12-10.9 | Jointing torque | 55 Nm | ||
| Torque angle | 90 ° | ||||
| E60/E61/E63/E64/E65 | M12-8.8 | Jointing torque | 30 Nm | ||
| Torque angle | 90 ° | ||||
| E83 | M12-10.9 | Jointing torque | 30 Nm | ||
| Torque angle Screw with ribbed teeth + double stage flexible disc | 90 ° | ||||
| 2AZ | Coupling propeller shaft to transmission | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 | 60 Nm | |
| E32/E31 | M12 | 95 Nm | |||