11 14 005 Replacing front crankshaft radial seal (N52K)

WARNING: This page is about a different variant/trim than selected.

Special tools required:

11 9 221
11 9 222
11 9 223
11 9 224
11 9 231
11 9 232
11 9 233

Necessary preliminary tasks:

Remove VIBRATION DAMPER

IMPORTANT: Do not release central bolt.
If the central bolt is released, the sprocket wheels of the timing chain and the oil pump will no longer be non - positively connected to the crankshaft. Inlet and exhaust camshafts can turn in relation to crankshaft.
Risk of damage!

Fig 1: Central Bolt

Courtesy of BMW OF NORTH AMERICA, INC.

Turn back special tool 11 9 222 .

Push special tool 11 9 221 onto crankshaft.

IMPORTANT: When screws are tightened down (special tool 11 9 224) , crankshaft radial seal is pressed inwards approx. 1 mm and thus slackened for subsequent removal.

Insert screws (special tool 11 9 224 ) and tighten down to approx. 20 Nm.

Fig 2: Special Tools (11 9 221), (11 9 222) And (11 9 224)

Courtesy of BMW OF NORTH AMERICA, INC.

Insert screws (special tool 11 9 223 ) and screw in until they make contact without play.

IMPORTANT: Do not overload special tool 11 9 223 (metal screws).

Fig 3: Special Tool (11 9 223)

Courtesy of BMW OF NORTH AMERICA, INC.

Remove screws (special tool 11 9 224 ).

Fig 4: Special Tool (11 9 224)

Courtesy of BMW OF NORTH AMERICA, INC.

Insert screw (special tool 11 9 222 ) carefully and slowly withdraw crankshaft radial seal (1).

Fig 5: Special Tool (11 9 222)

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Clean sealing surface (1) and degrease thoroughly in area of housing partition.

Apply a light coat of oil to running surface (2) of crankshaft radial seal.

Fig 6: Sealing And Running Surface

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Support bushing (1) is contained in scope of delivery of crankshaft radial seal (2).
When crankshaft radial seal (2) is installed, only support bushing (1) may be used as a slip bushing.

Crankshaft radial seal (2) has a groove on both left and right sides.

IMPORTANT: After installation, the grooves must be filled with sealing compound.

Fig 7: Crankshaft Radial Seal And Support Bushing

Courtesy of BMW OF NORTH AMERICA, INC.

Attach support bushing (2) with crankshaft radial seal (1).

Push on crankshaft radial seal (1) in direction of arrow.

Fig 8: Pushing Crankshaft Radial Seal

Courtesy of BMW OF NORTH AMERICA, INC.

Pay attention to opening on crankshaft radial seal (1) on left and right.

Remove support bushing (2).

Fig 9: Crankshaft Radial Seal And Support Bushing

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: The following text describes installation and sealing between the engine block and crankshaft radial seal.
The engine block will not be leakproof at the outside of the crankshaft radial seal if you fail to comply with the individual work steps and the work sequence.

NOTE: The required parts are available from the BMW Parts Service (EPC).

Remove screw caps (1) from injector (2).

Screw on metering needle.

Insert piston for pressing out.

Injector (2) contains the sealing compound Loctite, manufacturer's number 128357.

Bottle (3) contains the primer Loctite, manufacturer's number 171000.

Fig 10: Screw Caps, Injector And Bottle

Courtesy of BMW OF NORTH AMERICA, INC.

Fit special tool 11 9 232 .

Coat both grooves on crankshaft radial shaft seal with Loctite primer, manufacturer's number 171000, and expose to air for approx. one minute.

Fig 11: Special Tool (11 9 232)

Courtesy of BMW OF NORTH AMERICA, INC.

Draw in crankshaft radial seal with special tool 11 9 231 in conjunction with special tool 11 9 233 until flush.

Fig 12: Crankshaft Radial Seal And Support Bushing

Courtesy of BMW OF NORTH AMERICA, INC.

Before filling with sealing compound:

Moisten brush with Loctite primer, manufacturer's number 171000. Insert brush as far as possible into grooves (1) on crankshaft radial seal in order to coat housing partition on engine block.

Fig 13: Grooves On Crankshaft Radial Seal

Courtesy of BMW OF NORTH AMERICA, INC.

Using injector (2), fill both grooves (3) flush with Loctite sealing compound, manufacturer's number 128357.

Fig 14: Injector And Grooves On Crankshaft Radial Seal

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Loctite primer, manufacturer's number 171000, binds the Loctite sealing compound, manufacturer's number 128357, and prevents leakage.

Coat surface of sealing compound in both grooves (1) with Loctite primer, manufacturer's number 171000.

Fig 15: Grooves On Crankshaft Radial Seal

Courtesy of BMW OF NORTH AMERICA, INC.

Assemble engine.