11 31 036 Removing And Installing/Replacing Left Exhaust Camshaft (N62/N62TU)

WARNING: This page is about a different variant/trim than selected.

(cylinder bank 5 to 8)

Necessary preliminary tasks:

Remove servomotor for left eccentric shaft . See 11 37 022 REMOVING AND INSTALLING/REPLACING SERVOMOTOR FOR LEFT ECCENTRIC SHAFT (N62/N62TU) .
Remove ignition coils on cylinder bank 5 to 8
Remove left cylinder head cover . See 11 12 005 REMOVING AND INSTALLING/SEALING LEFT CYLINDER HEAD COVER (N62/N62TU) .
Remove spark plugs on cylinder bank 5 to 8
Remove left inlet and exhaust adjustment units . See 11 36 047 REMOVING AND INSTALLING/REPLACING INLET AND EXHAUST ADJUSTMENT UNITS ON LEFT SIDE (N62/N62TU) .

Remove slide rail (1).

Fig 1: Identifying Slide Rail

Courtesy of BMW OF NORTH AMERICA, INC.

Rotate exhaust camshaft at hexagon head until exhaust cam on cylinder (6) is facing upwards.

Fig 2: Locating Exhaust Camshaft On Cylinder

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Camshaft bearing caps of cylinders 1 to 4 and 5 to 8 must not be mixed up.

NOTE: Bearing caps of exhaust camshaft are marked on cylinder bank 5 to 8 with R A1 to R A5 from inlet side.

Release nuts and remove bearing cap R A1.

Fig 3: Identifying Camshaft Bearing Caps Of Cylinders

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Retaining clips (1) for oil line are fitted on bearing caps 3 and 5.

Release nuts on bearing caps R A2 to R A5.

Fig 4: Identifying Retaining Clips For Oil Line Fitted On Bearing Caps

Courtesy of BMW OF NORTH AMERICA, INC.

Remove bearing caps R A2 to R A5.

Fig 5: Identifying Camshaft Bearing Caps Of Cylinders

Courtesy of BMW OF NORTH AMERICA, INC.

Remove exhaust camshaft (1).

Fig 6: Identifying Exhaust Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

If necessary, replace plain compression rings (1).

IMPORTANT: Plain compression rings (1) can easily break.

Plain compression rings (1) are engaged at joint.

Press compression ring (1) on one side into groove, pull up on other side and remove catch.

Carefully pull compression ring (1) apart and remove towards front.

Fig 7: Pulling Compression Ring

Courtesy of BMW OF NORTH AMERICA, INC.

If necessary, replace sensor gear (1).

Release screw (2) and remove sensor gear (1).

Fig 8: Identifying Sensor Gear And Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Installation of exhaust camshaft is described separately from removal.

Clean all bearings and cams of exhaust camshaft and lubricate with engine oil.

NOTE: Camshaft has a groove and sensor gear has a lug for fastening purposes.

Fig 9: Locating Camshaft Groove And Sensor Gear

Courtesy of BMW OF NORTH AMERICA, INC.

Fit sensor gear (1) and align to groove in camshaft.

Insert screw (2) and tighten down.

Tightening torque 11 31 14AZ . See ENGINE - TIGHTENING TORQUES (N62TU V8) .

Fig 10: Identifying Sensor Gear And Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Installing plain compression rings (1):

IMPORTANT: Plain compression rings (1) can easily break.

Carefully pull compression ring (1) apart and install from front.

Press compression ring (1) on one side into groove, install catch on other side.

Fig 11: Installing Plain Compression Rings

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Rocker arms (1) of exhaust camshaft are of same design as rocker arms of inlet camshaft.

The classification 3 shown in the graphic has no effect on the function on the exhaust camshaft.

Fig 12: Locating Rocker Arms Of Exhaust Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Rocker arms (1) slip slightly when exhaust camshaft is fitted.
Make sure rocker arms (1) are secured as illustrated on hydraulic valve clearance compensating elements and on valves.

Used rocker arms (1) may only be reused in the same position.

Align rockers (1) straight.

Fig 13: Identifying Rocker Arms

Courtesy of BMW OF NORTH AMERICA, INC.

Lubricate exhaust camshaft and bearing caps with engine oil.

Install exhaust camshaft (1).

Rotate exhaust camshaft (1) until exhaust cam on cylinder 6 is facing upwards.

Fig 14: Identifying Exhaust Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Check dowel sleeves (2) for damage and correct installation position.

Ends of compression rings (1) point upwards.

Make sure compression rings (1) are engaged at ends.

Fig 15: Locating Dowel Sleeves And Compression Rings

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Camshaft bearing caps of cylinders 1 to 4 and 5 to 8 must not be mixed up.

NOTE: Bearing caps of exhaust camshaft are marked on cylinder bank 5 to 8 with R A1 to R A5 from inlet side.

Fit bearing caps R A2 to R A5.

Fig 16: Identifying Camshaft Bearing Caps Of Cylinders

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Retaining clips (1) for oil line are fitted on bearing caps 3 and 5.

Insert nuts and tighten by hand without play.

Tighten down nuts on bearing caps R A2 to R A5 in 1/2 turn increments evenly from inside to outside.

Tightening torque 11 31 1AZ . See ENGINE - TIGHTENING TORQUES (N62TU V8) .

Fig 17: Identifying Retaining Clips For Oil Line Fitted On Bearing Caps

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Camshaft bearing caps of cylinders 1 to 4 and 5 to 8 must not be mixed up.

Fit bearing cap R A1 in such a way that marking is legible from inlet side.

Install nuts and tighten down.

Tightening torque 11 31 1AZ . See ENGINE - TIGHTENING TORQUES (N62TU V8) .

Fig 18: Identifying Camshaft Bearing Caps Of Cylinders

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: A gasket (2) is installed between cylinder head and slide rail (1).

Replace gasket (2) and preinstall on slide rail (1).

Fig 19: Identifying Cylinder Head And Slide Rail

Courtesy of BMW OF NORTH AMERICA, INC.

Install slide rail (1) with gasket, insert screw and tighten down.

Fig 20: Identifying Slide Rail

Courtesy of BMW OF NORTH AMERICA, INC.

Rotate exhaust camshaft against direction of rotation until cam on 5th cylinder points upwards at an angle as shown in illustration.

Fig 21: Locating Exhaust Camshaft

Courtesy of BMW OF NORTH AMERICA, INC.

Install inlet and exhaust adjustment unit on left side . See 11 36 047 REMOVING AND INSTALLING/REPLACING INLET AND EXHAUST ADJUSTMENT UNITS ON LEFT SIDE (N62/N62TU) .

Install spark plugs on cylinder bank 5 to 8.

Install left cylinder head cover . See 11 12 005 REMOVING AND INSTALLING/SEALING LEFT CYLINDER HEAD COVER (N62/N62TU) .

Install ignition coils on cylinder bank 5 to 8.

Assemble engine.