37 14 Electric Components
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2014 BMW X6, 2013 BMW X6, 2012 BMW X6, 2011 BMW X6, and 2010 BMW X6. However, it is still accessible from the selected car via links, so may be relevant.
ELECTRIC COMPONENTS - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Bracket, ride-height sensor, to body | E70, E71 | M6 | 8 Nm | |
| 2AZ Bracket ride level sensor to rear axle carrier | E70, E71 | M6 | 8 Nm | |
| 3AZ Ride level sensor to holder | E70, E71 | M5 | 4.6 Nm | |
| 4AZ Sensor lever, ride-height sensor to jointed rod | E70, E71 | M6 | Replace nut | 8 Nm |
| 5AZ Jointed rod to upper control arm | E70, E71 | M6 | Replace nut | 8 Nm |
| 6AZ Jointed rod to swinging arm | E70, E71 | M6 | Replace nut | 8 Nm |
| 7AZ Lateral acceleration sensor to body | E70, E71 | M6 | Replace nuts | 8 Nm |
| 8AZ Control unit Dynamic Drive ECU to cockpit support structure | E70, E71 | M5 x 15 | 6 Nm | |
| 9AZ Valve block to holder | E70, E71 | M6 | 8 Nm | |
| 10AZ Holder, valve block, to body | E70, E71 | M6 | Replace nuts | 8 Nm |
| 11AZ Dynamic Drive pressure line to valve block | E70, E71 | 35 Nm | ||
| 12AZ Return line to valve block | E70, E71 | 40 Nm | ||
| 13AZ Control lines for oscillating motor, front, to valve block | E70, E71 | M14 | 35 Nm | |
| 14AZ Control lines for oscillating motor, rear, to valve block | E70, E71 | M14 | 35 Nm | |
| 15AZ Connecting nuts, hydraulic lines (pressure line/control lines) | E70, E71 | 30 Nm | ||
| 16AZ Connecting nuts, hydraulic lines (return) | E70 | 35 Nm | ||
| 17AZ Line holder/pipe holder/holder | E70, E71 | M6 | 8 Nm | |
| E70, E71 | M8 | 20.5 Nm | ||
| 18AZ Control lines to oscillating motor | E70, E71 | 30 Nm | ||
| 19AZ Protective plate to rear axle carrier | E70, E71 | M10 | 38 Nm | |
| E70, E71 | M6 | 8 Nm | ||
| 20AZ Retaining bar, stabilizer, to front axle carrier | E70, E71 | M10 | 60 Nm | |
| 21AZ Retaining bracket, stabilizer bar to rear axle support | E70, E71 | M10 | 56 Nm | |
| 22AZ Screw pins for pipe holder | E70 | Replace screw pins | 1.5 Nm | |
| 23AZ Spring-type actuator to oscillating motor, front | E70 | 30 Nm | ||
| 24AZ Pressure relief valve to oscillating motor, front | E70, E71 | 14 + 4 Nm | ||
| 25AZ Line holder for control lines to front axle oscillating motor | E70, E71 | 3 Nm | ||
| 26AZ Lines to spring-type actuator | E70/E71 | 14 Nm | ||
| 27AZ Block screw connection, hydraulic lines | E70/E71 | 12 Nm |